04-24-2015, 11:22 AM | #23 |
Captain
449
Rep 992
Posts |
|
Appreciate
0
|
05-15-2015, 04:36 PM | #25 |
Major
248
Rep 1,436
Posts |
congrats !! do you have dp with it ?!
__________________
F30 328i - 8 auto.. JB4-EWG harness, OCC, Injen Intake, AFE Scoop, AFE dp, AA axle-back - H&R springs, H&R Rear SB, Front Strut, F&R BMS spacers..
|
Appreciate
0
|
05-15-2015, 05:17 PM | #28 |
Banned
104
Rep 388
Posts |
|
Appreciate
0
|
05-16-2015, 12:19 PM | #29 |
Second Lieutenant
65
Rep 246
Posts |
|
Appreciate
0
|
05-17-2015, 01:32 AM | #32 |
Major
248
Rep 1,436
Posts |
|
Appreciate
0
|
05-17-2015, 09:59 AM | #33 |
Banned
104
Rep 388
Posts |
Not interested in down pipes. I'm looking for a good tune that isn't gonna give me any future probs. Just reading about this is giving me a headache. Some say one is better than the other. Some make the car jerky. Some are blowing engines. Some give the car more power. Don't know what to believe. My preference is Dinan, but for double the price of anything else, I'm not spending that kinda $ LOL
|
Appreciate
0
|
05-17-2015, 10:17 AM | #34 | |
Major
248
Rep 1,436
Posts |
Quote:
|
|
Appreciate
0
|
05-17-2015, 11:22 AM | #35 |
Second Lieutenant
65
Rep 246
Posts |
|
Appreciate
0
|
05-17-2015, 01:02 PM | #36 |
Banned
104
Rep 388
Posts |
|
Appreciate
0
|
05-17-2015, 02:01 PM | #37 |
Banned
104
Rep 388
Posts |
|
Appreciate
0
|
05-17-2015, 02:04 PM | #38 | |
BimmerPost Supporting Vendor
24095
Rep 190,633
Posts |
Quote:
__________________
Check out our current sale by clicking on this link!
https://x-ph.com/sale/ Phone number 702-494-9435 |
|
Appreciate
0
|
05-18-2015, 09:47 PM | #39 |
Major
327
Rep 1,490
Posts |
I have the AA exhaust. Been very happy with it, although it rattles a bit on start up - I don't blame the exhaust, but the installers.
I wish I could take some nice videos because the car makes a good noise along with my Injen intake. As for DP, I'd avoid it - reason being, the CEL and smell. It's such a pain taking it on/off for service. If you get a JB4 + DP, you may run into issues with certain maps exceeding the power limits of this motor. It will give you a good bump in HP and make nice noises though.
__________________
Current: 17 Mustang GT no bmw
Gone but not forgotten: 07 E90 335I, 04 UA6, 95 E36, 04 EP3, 16 S550 EB, 14 F30 328I Stg 1, 08 E90 328I |
Appreciate
0
|
05-29-2018, 09:24 PM | #41 |
New Member
2
Rep 17
Posts |
Hello all, I’m being quoted $270 get this installed in f30 N26 engine. Is this a fair price? The estimate also mentions welding- thought it was just a clamp and no welding was required? Any advice will be greatly appeciated. Thanks
|
Appreciate
0
|
05-30-2018, 12:52 AM | #42 |
Brigadier General
3072
Rep 4,315
Posts |
that's way too much. you should install it yourself. even if you didn't have a floor jack and stands. you could reverse it close to the end of a loading dock to have roomy access. cut the mid-pipe at the dimple, remove the hangars and old axle back. install hangars, new axle back and clamp.
|
Appreciate
0
|
06-02-2018, 07:26 PM | #43 | |
New Member
2
Rep 17
Posts |
Quote:
|
|
Appreciate
0
|
06-05-2018, 04:49 PM | #44 |
BimmerPost Supporting Vendor
24095
Rep 190,633
Posts |
Post a video
__________________
Check out our current sale by clicking on this link!
https://x-ph.com/sale/ Phone number 702-494-9435 |
Appreciate
0
|
Post Reply |
Bookmarks |
|
|