[Joetums_F30]

Anyone know if I could I use the BMS Stage 1 BMW Performance Tuner with a AFE catless downpipe to hide the O2 code or would I need to use the F Series N55 JB4 to hide that message

[mookie45]

Originally Posted by Joetums_F30

Anyone know if I could I use the BMS Stage 1 BMW Performance Tuner with a AFE catless downpipe to hide the O2 code or would I need to use the F Series N55 JB4 to hide that message

BMS Stage 1 will not delete code.

You will need a JB4, BMS Can Flap Module, I think VSRF sells an O2 sensor simulator, or software flash from 3rd party tuner.

[mike@x-ph.com]

Originally Posted by Joetums_F30

Anyone know if I could I use the BMS Stage 1 BMW Performance Tuner with a AFE catless downpipe to hide the O2 code or would I need to use the F Series N55 JB4 to hide that message

mookie45 said it perfectly

[Chicken_Joe]

The io2 CatSim will fix the CEL. I have one on my car

[redbullfan]

Originally Posted by Chicken_Joe

The io2 CatSim will fix the CEL. I have one on my car

are you 100% positive it will fix it?

[Chicken_Joe]

Originally Posted by redbullfan

are you 100% positive it will fix it?

Well I had my cat simulator installed last Friday and so far I have driven my car over 120 miles and there has been no check engine light. I can double check and make sure that the code is off in the car but I have been reassured that it work on the F chassis N55

[redbullfan]

Originally Posted by Chicken_Joe

Well I had my cat simulator installed last Friday and so far I have driven my car over 120 miles and there has been no check engine light. I can double check and make sure that the code is off in the car but I have been reassured that it work on the F chassis N55

Not that i dont belive you, i just want to know if the readiness sensor for the emssions is ready and i can pass inspection with it.

[Chicken_Joe]

Originally Posted by redbullfan

Not that i dont belive you, i just want to know if the readiness sensor for the emssions is ready and i can pass inspection with it.

Yes you will pass an emissions test with the unit. You just need to set the JB on stock map and drive the car until the drive cycle is completed and then go in and get the emissions test done.

[Joetums_F30]

Originally Posted by mookie45

BMS Stage 1 will not delete code.

You will need a JB4, BMS Can Flap Module, I think VSRF sells an O2 sensor simulator, or software flash from 3rd party tuner.

Thank you

[jgoens]

Originally Posted by Chicken_Joe

Well I had my cat simulator installed last Friday and so far I have driven my car over 120 miles and there has been no check engine light. I can double check and make sure that the code is off in the car but I have been reassured that it work on the F chassis N55

Good news. Assuming you have the auto clear off on JB4 and have you checked for any faults? I say this, because I would not get a CEL but when I checked codes via JB4 I had the catless DP installed code.

[Chicken_Joe]

Originally Posted by jgoens

Good news. Assuming you have the auto clear off on JB4 and have you checked for any faults? I say this, because I would not get a CEL but when I checked codes via JB4 I had the catless DP installed code.

I will need to check that actually.

[Joetums_F30]

Originally Posted by mike@x-ph.com

mookie45 said it perfectly

I only see the VSRF O2 sensor simulator for the E series, do you happen to know if they make one for the F?

[mike@x-ph.com]

Originally Posted by Joetums_F30

I only see the VSRF O2 sensor simulator for the E series, do you happen to know if they make one for the F?

The same N55 one is used for E and F chassis

[Joetums_F30]

Think I like the BMS Can Flap Module option the best, no cutting wires