[shawnsheridan]

Originally Posted by fe7565

Hi Shawn, could you send me the link also for CEL check/clear, and coding a 2012 328i? Thank you.

PM sent.

[fe7565]

Thank you for the superfast reply/PM and the detailed guide!!!

[shawnsheridan]

Originally Posted by fe7565

Thank you for the superfast reply/PM and the detailed guide!!!

[bmw_fascinated]

Today I had my car coded for led turn lights, but the LEDs are not working (stay completely off).

It has been coded:
-Warm and Kaltüberwachung nicht_aktiv,
-pwm_level1 set to 89
-Ueberspannungsschutz nicht_aktiv
-Is_LED active.

I only rarely see that UE_SPG_SCHUTZ is set to nicht aktiv, could this be an issue?
Tried different LEDs but still no luck.

Any suggestions?

[Billfitz]

Originally Posted by bmw_fascinated

-Ueberspannungsschutz nicht_aktiv
-pwm_level1 set to 89

Those are not on my cheat sheet.

[soundwave]

Hi Shawn, the latest sw version + data files would be greatly appreciated!

[shawnsheridan]

Originally Posted by soundwave

Hi Shawn, the latest sw version + data files would be greatly appreciated!

PM sent.

[Arturino]

Hi Shawn,

Would it be possible to have the latest sw version + data files? Some latest coding guide for the 3 series would be very nice to have!
Thanks!

[shawnsheridan]

Originally Posted by Arturino

Hi Shawn,

Would it be possible to have the latest sw version + data files? Some latest coding guide for the 3 series would be very nice to have!
Thanks!

PM sent.

[Arturino]

Thanks!

[Luiz Bicudo]

Thanks for the files Shawn!

Last year I had total success coding my 2016 328i using spzd 3.57.3.002.
I just replaced it by a 2017 320i, and with last year's setup no ecu's CAFD file was found.
I updated to spzd 62.1.003 and now most of the CAFD had a match, but still 6 ECU's, among them FEM_BODY (CAFD_00000794_015_048_005) are lacking.
Could you tell me if there's any workaround, or I'll just have to wait for the next version of spzd?

Thanks

[shawnsheridan]

Originally Posted by Luiz Bicudo

Thanks for the files Shawn!

Last year I had total success coding my 2016 328i using spzd 3.57.3.002.
I just replaced it by a 2017 320i, and with last year's setup no ecu's CAFD file was found.
I updated to spzd 62.1.003 and now most of the CAFD had a match, but still 6 ECU's, among them FEM_BODY (CAFD_00000794_015_048_005) are lacking.
Could you tell me if there's any workaround, or I'll just have to wait for the next version of spzd?

Thanks

Your car has nothing newer than 62.1 on it, because nothing newer exists yet. So there is no reason 62.1 woukd have missing CAFD, nor would next version be needed or beneficial.

You need to make sure your 62.1 extracted properly and all files are present.

[AJ2206]

Hi Shawn,
I seem to have lost my display (dialled list, song names etc.) on my instrument cluster which I used to control via the steering wheel knob. SJ00 told me you addressed this issue by suggesting the following:
HU_NBT => BASIS_KOMBI_MMI_LIST = aktiv
HU_NBT => KOMBI_CIC = kombi_low

Would it be too tedious to explain me steps on how do I code the above (Connect->F030->Expert mode-> coding-> etc....)? I am fairly new to coding but have latest Esys, data files (PSdZdata v61.4) and have connected to the car before for a few tweaks.

[kabongSteve]

Hi Shawn, the latest sw version + data files would be greatly appreciated!

[shawnsheridan]

Originally Posted by AJ2206

Hi Shawn,
I seem to have lost my display (dialled list, song names etc.) on my instrument cluster which I used to control via the steering wheel knob. SJ00 told me you addressed this issue by suggesting the following:
HU_NBT => BASIS_KOMBI_MMI_LIST = aktiv
HU_NBT => KOMBI_CIC = kombi_low

Would it be too tedious to explain me steps on how do I code the above (Connect->F030->Expert mode-> coding-> etc....)? I am fairly new to coding but have latest Esys, data files (PSdZdata v61.4) and have connected to the car before for a few tweaks.

Connect => Read FA (VO) => Activate FA (VO) => Read SVT (VCM) => Right-Click on the HU_NBT ECU CAFD and select Read Coding Data => Expand the CAFD Folder by clicking + symbol => Right-Click on the CAFD file and select Edit => Edit CAFD (both FDL Codes above) as desired => Click the Blue Floppy Disc Icon to Save CAFD => Click the green back arrow icon => Right-Click on the CAFD file => Select FDL CODE.

[shawnsheridan]

Originally Posted by kabongSteve

Hi Shawn, the latest sw version + data files would be greatly appreciated!

PM sent.

[EL Jeffe 5]

Finally got my cable
Where can I get latest version form F10?
how much space do I need on computer?
What is percentage of me bricking my car in garage and bagging dealer to reprogram my car?

Thanks in advance

[shawnsheridan]

Originally Posted by EL Jeffe 5

Finally got my cable
Where can I get latest version form F10?
how much space do I need on computer?
What is percentage of me bricking my car in garage and bagging dealer to reprogram my car?

Thanks in advance

PM sent. Space if just Coding (PSdZdata Lite) is around 3 Gb and if Programming (PSdZData Full) around 110 Gb. Follow guides and you should not brick anything.

[EL Jeffe 5]

Originally Posted by shawnsheridan

PM sent. Space if just Coding (PSdZdata Lite) is around 3 Gb and if Programming (PSdZData Full) around 110 Gb. Follow guides and you should not brick anything.

That was amazing fast Major THANKS

[Jonryan26]

Shawn, Could you please send me the latest files? Thanks!

[shawnsheridan]

Originally Posted by Jonryan26

Shawn, Could you please send me the latest files? Thanks!

PM sent.

[superwm]

Shawn, pls could you send me the latest files too? Tks!