[perryo91]

     Featured on BIMMERPOST.com

My dad and I's second attempt was a success. After watching a couple youtube videos and a 90% first attempt; we knocked it out of the park.

I 100% recommend everyone wrap their drip rails too. The first attempt we didn't wrap the rail, but made sure we did it on second. Also the sharkfin was a biatch to remove and wrap, but necessary to complete the look.

Highly recommended to DIY this as it will take less than 2 hours and material cost is dirt cheap!

Used Avery gloss black.

[7iM3less]

Originally Posted by perryo91

My dad and I's second attempt was a success. After watching a couple youtube videos and a 90% first attempt; we knocked it out of the park.

I 100% recommend everyone wrap their drip rails too. The first attempt we didn't wrap the rail, but made sure we did it on second. Also the sharkfin was a biatch to remove and wrap, but necessary to complete the look.

Highly recommended to DIY this as it will take less than 2 hours and material cost is dirt cheap!

Used Avery gloss black.

Avery's a great choice

[trilltx]

If I could do this myself, I totally would.

[perryo91]

Originally Posted by KC328_F30

Avery's a great choice

Yeah for sure, it was really easy to lift off and place back, I think if I were to do this again I'd go with 3M just to compare and contrast.

Originally Posted by trilltx

If I could do this myself, I totally would.

I think it's possible, it will take a little longer and you'd probably have to use those little magnets they sell to hold the film 100% in place. But yeah, it's gonna be tough

[SoCal_NSX]

Nice job!

My buddy's shop(Endless auto salon) had a Memorial Day special and got mine done for $180. Love the look!!!

[Speedwell-Industries]

Originally Posted by KC328_F30

Avery's a great choice

Originally Posted by SoCal_NSX

Nice job!

My buddy's shop(Endless auto salon) had a Memorial Day special and got mine done for $180. Love the look!!!

Looks incredible!! Simple but very tasteful mod

[perryo91]

Originally Posted by SoCal_NSX

Nice job!

My buddy's shop(Endless auto salon) had a Memorial Day special and got mine done for $180. Love the look!!!

Thats a really good price I just like making my life difficult and DIY'ing I paid a total of $100 for the materials for 2 attempts!

[SoCal_NSX]

Originally Posted by perryo91

Thats a really good price I just like making my life difficult and DIY'ing I paid a total of $100 for the materials for 2 attempts!

Yeah, that was a deal I couldn't pass up.

I try to stick to the easy DIY mods

[mlev]

Originally Posted by perryo91

Thats a really good price I just like making my life difficult and DIY'ing I paid a total of $100 for the materials for 2 attempts!

Looks good...getting this done this Friday. Did you use Avery SW900 Gloss Black?

[perryo91]

Originally Posted by mlev

Looks good...getting this done this Friday. Did you use Avery SW900 Gloss Black?

Good choice! I think every light colored car should have a black roof

Yes sir! very forgiving material!

And we'll see how it lasts under florida heat, so far so good!

[F3rst0rder]

How’s the fade on a roof wrap???

[perryo91]

Originally Posted by F3rst0rder

How’s the fade on a roof wrap???

There shouldn't be any fade until 5+ years.

[arom]

Did you wrap the fin with one piece?

[perryo91]

Originally Posted by arom

Did you wrap the fin with one piece?

Yes sir, was a pain in the butt and had two attempts before getting the final one down just right!

Worth the trouble though, I really didn't want any seams on it.