[MYF30ROCKS]

     Featured on BIMMERPOST.com

Retrofitting NBT EVO ID6 to my 13 F30 had CIC High Prof Nav and Enhanced BT

I bought the NBT EVO HU, Touch I-drive from 2016 F30 bought Touch ECU from ebay, 10.25 touch screen from 18 X6, Quad lock harness with other parts from ebay.

NBT EVO HU got precoded before installing from one of the coder, see below picture

Everything is connected except the mic, if all works then I will route the mic wire. When I turn on, everything is blank, except some time vent temp on radio comes on and goes quickly.
When I connect with bimmer code” "coding head unit not possible because it is not in its original state"

Because my screen is blank and nothing turns on, coding guy says your screen is bad and cant see what’s wrong.

Looking for some inputs before I go buy another screen.

I tried to connect another LVDS cable, direct quad lock, its same status.

Appreciate your inputs….thank you
-----------------------------------------------------------
Update 1
So far
-Touch Screen is working- LVDS cable issue, polarity swapped red and black wire. Also 4 pin rotated 180deg
- 360 Cameras- have to move Camera pins
Pin 18 at quadlock to pin 21
Pin 28 at quadlock to pin 24
Pin 27 at quadlock to pin 23
- rest all AM, FM bit poor quality, usb( both armrest and glovebox), CarPlay, M-lap etc

- Navigation is not working, not able to install maps
- Idrive Touch not working: still root causing
--------------------------------------------------

[JuniorTech]

Originally Posted by MYF30ROCKS

Retrofitting NBT EVO ID6 to my 13 F30 had CIC High Prof Nav and Enhanced BT

I bought the NBT EVO HU, Touch I-drive from 2016 F30 bought Touch ECU from ebay, 10.25 touch screen from 18 X6, Quad lock harness with other parts from ebay.

NBT EVO HU got precoded before installing from one of the coder, see below picture

Everything is connected except the mic, if all works then I will route the mic wire. When I turn on, everything is blank, except some time vent temp on radio comes on and goes quickly.
When I connect with bimmer code” "coding head unit not possible because it is not in its original state"

Because my screen is blank and nothing turns on, coding guy says your screen is bad and cant see what’s wrong.

Looking for some inputs before I go buy another screen.

I tried to connect another LVDS cable, direct quad lock, its same status.

Appreciate your inputs….thank you

i can help you
chek your PM

[Siki78]

If you have combox before and you remove it did you close most or you leave it open?

[MYF30ROCKS]

Originally Posted by JuniorTech

i can help you
chek your PM

Thank you much for helping me to resolve the issues, I really appreciate you help👍

[MYF30ROCKS]

Originally Posted by Siki78

If you have combox before and you remove it did you close most or you leave it open?

Thank you for responding, Yes, have combox and just connected with jumper as recommended by JuniorTech!👆

[rlesko]

Originally Posted by MYF30ROCKS

Thank you much for helping me to resolve the issues, I really appreciate you help👍

If your issue was resolved please post the resolution here

[Siki78]

It is already written everything and you can see his error. Most was a problem stay open

[MYF30ROCKS]

Update 1


Still working on resolving issues
So far
-Touch Screen is working- LVDS cable issue, polarity swapped red and black wire. Also 4 pin rotated 180deg
- 360 Cameras- have to move Camera pins
Pin 18 at quadlock to pin 21
Pin 28 at quadlock to pin 24
Pin 27 at quadlock to pin 23
- rest all AM, FM bit poor quality, usb( both armrest and glovebox), CarPlay, M-lap etc

- Navigation is not working, not able to install maps
- Idrive Touch not working: still root causing

I will update as I progress

[rlesko]

Originally Posted by MYF30ROCKS

Still working on resolving issues
So far
-Touch Screen is working- LVDS cable issue, polarity swapped red and black wire. Also 4 pin rotated 180deg
- 360 Cameras- have to move Camera pins
Pin 18 at quadlock to pin 21
Pin 28 at quadlock to pin 24
Pin 27 at quadlock to pin 23
- rest all AM, FM bit poor quality, usb( both armrest and glovebox), CarPlay, M-lap etc

- Navigation is not working, not able to install maps
- Idrive Touch not working: still root causing

I will update as I progress

Did you install new FM amplifier with FM2 cable? Also, I was never able to code my touch controller for my NBT Evo + ATM retrofit, I just gave up on that aspect.

With regards to navi not working, do you have an ATM or a GPS port from your Evo HU?

[MYF30ROCKS]

Originally Posted by rlesko

Did you install new FM amplifier with FM2 cable? Also, I was never able to code my touch controller for my NBT Evo + ATM retrofit, I just gave up on that aspect.

With regards to navi not working, do you have an ATM or a GPS port from your Evo HU?

FM amplifier not yet, will be doing next few weeks

Navigation- GPS port

[MYF30ROCKS]

Update 2

No success Navigation to work yet
MY original NBT EVO HU came without Nav port
Got retrofitted

Yesterday i was seeing Navigation loading and starting information on screen

Today I reconnected USB ports
Now it shows me connect usb device with correct activation code to start navigation.
Hope some chime if they seen this in past and resolved

[MYF30ROCKS]

Update 3

No success Navigation to work yet


I-drive touch control issue resolved, had wrong Touch ECU part number.
Its connected and working fine

connected Pins 3 and 4 on i-drive to terminal 11 and 9.

[MYF30ROCKS]

Originally Posted by rlesko

Did you install new FM amplifier with FM2 cable? Also, I was never able to code my touch controller for my NBT Evo + ATM retrofit, I just gave up on that aspect.

With regards to navi not working, do you have an ATM or a GPS port from your Evo HU?

Do you know what's the part number of FM amplifier?

Just want to confirm before buy 65209231178 Antenna amplifier AM/FM

Thank you

[rlesko]

Originally Posted by MYF30ROCKS

Do you know what's the part number of FM amplifier?

Just want to confirm before buy 65209231178 Antenna amplifier AM/FM

Thank you

Cable: 61119372322
Amplifier: 65209231178

By the way, you say you replaced the ECU - the touch ECU?