03-07-2018, 02:13 PM | #1 |
New Member
1
Rep 7
Posts |
Square 255/35/19 on f32?
Hi guys, after looking extensively, I did not find any definitive answer.
Is it possible to run a square setup of 255/35/19 on a f32 xdrive m performance? If yes, what is the ideal wheel width and offset? Thanks |
03-07-2018, 02:59 PM | #3 | |
Brigadier General
3080
Rep 4,330
Posts |
Quote:
http://f30.bimmerpost.com/forums/sho...35%2F19+square |
|
Appreciate
0
|
03-08-2018, 06:05 PM | #6 |
Banned
4488
Rep 10,473
Posts |
Yes it will work if the wheels are right. That means not repurposing BMW F32 OEM 19” Staggered Wheels.
|
Appreciate
0
|
03-08-2018, 06:18 PM | #7 |
Second Lieutenant
96
Rep 219
Posts |
Has anyone bought new factory rear wheels and used a 12mm spacer to get to 35et on an f3x? Thinking of adding two rear wheels and tires to match my oem set and going 255 square.
|
Appreciate
0
|
03-08-2018, 06:23 PM | #8 |
Banned
4488
Rep 10,473
Posts |
255 will not fit correctly on front wheels (8.0”) of BMW OEM F3x 19” staggered setup.
|
Appreciate
0
|
03-08-2018, 06:35 PM | #9 | |
Second Lieutenant
96
Rep 219
Posts |
Quote:
Thoughts? |
|
Appreciate
0
|
03-08-2018, 07:05 PM | #10 | |
Banned
4488
Rep 10,473
Posts |
Quote:
You really need to get the wheels out 18mm+. The reason I say 18mm+ is because several F32 owners (not all) claim 255/35/19 scrap the inside if turned totally to the right..so 20mm might fit the bill to be safe. That said, I don’t see 35 offset working. Using F32 OEM Front to F32 Rear for front http://www.willtheyfit.com/index.php...8-5&offset2=47 Using F82 OEM 437m front to F32 OEM Rear for front http://www.willtheyfit.com/index.php...8-5&offset2=47 Last edited by IK6SPEED; 03-08-2018 at 07:12 PM.. |
|
Appreciate
1
Canadian eh!95.50 |
03-08-2018, 10:14 PM | #11 | |
New Member
1
Rep 7
Posts |
Quote:
|
|
Appreciate
0
|
03-08-2018, 10:25 PM | #12 | |
Banned
4488
Rep 10,473
Posts |
Quote:
The reports MIGHT have been X-Drive only F32, you’d have to go back and search. As I do not have F32 I did not pay attention to every small factor. Going by memory. |
|
Appreciate
1
440mppk_qc1.00 |
03-09-2018, 10:58 AM | #13 |
Banned
4488
Rep 10,473
Posts |
|
Appreciate
1
440mppk_qc1.00 |
03-09-2018, 12:09 PM | #14 |
New Member
1
Rep 7
Posts |
I have also noticed that 437m are 19x9 +29, and the wheels that a plan to buy are 19x8.5 +35, so the inset for both wheels are virtually identical. Therefore, I might only need a 2-3mm spacer in the worst case scenario.
|
Appreciate
0
|
03-09-2018, 12:37 PM | #15 |
Brigadier General
3080
Rep 4,330
Posts |
i'm pretty sure 19x8.5 +35 with 255/35/19 will fit without rubbing the spring perch or strut, without a spacer.
with the above set up, i believe that if you add a spacer where the effective offset +29 or greater there is a possibility the outer front shoulder will rub the front wall of the fenderwell liner at full lock. Last edited by alohasurftoad; 02-02-2023 at 07:56 PM.. |
Appreciate
2
440mppk_qc1.00 Canadian eh!95.50 |
Post Reply |
Bookmarks |
|
|