[MissionPerformance]

DME Flashing Instructions

Pre-Requisites
-Even though it’s not necessary, we recommend you hook up a battery charger for this process. Also park your vehicle in such a way that it doesn’t block your driveway/road in case of failed flash.
-Start the engine and let it idle. Turn lights off, radio off, heater/ac off. Pretty much turn all of the accessories to off position. Connect the eNet cable from your vehicle to laptop and make sure your laptop has WiFi connection.

Directions
1. Start the program and Click on Scan. You might have to click on scan few times if the program fails to detect your car.

2. Once the vehicle is detected, click on Connect and then Unlock.

3. Go to DME, Flash, Write Memory.

4. After you see computer information loaded click on continue.
*You might have popup saying that coding data needs to be saved. Click OK and wait a second. Next popup will tell you if backup for successful.
*If you get an ERROR warning, or a message saying that computer is not present in the system, then DO NOT continue. Contact us with your VIN so we can see what is the issue.

6. Click on Continue and then select Flash Option, depending on what is Available/Desired.

7. If your computer is still on factory flash, it will ask you to perform Unlock. Click Yes.

8. Now this is very important. Next steps start the flash process that takes about 10 minutes or so. During this time, you can’t turn of ignition, though it will cycle by itself. When you start the process, make sure to leave the driver door in the same position (if it was open, don’t close it. If its closed, don’t open it).

9. Click on start and wait until process finishes up.

10. After a successful flash, you should get a Pop-Up asking to clear DTC codes. Click Yes to all.

11. After your ignition cycles On and Off, you are done.




Transmission Flashing Instructions

Pre-Requisites
-Even though it’s not necessary, we recommend you hook up a battery charger for this process. Also park your vehicle in such a way that it doesn’t block your driveway/road in case of failed flash.
-Start the engine and let it idle. Turn lights off, radio off, heater/ac off. Pretty much turn all of the accessories to off position. Connect the eNet cable from your vehicle to laptop and make sure your laptop has WiFi connection.

Directions
1. Start the program and Click on Scan. You might have to click on scan few times if the program fails to detect your car.

2. Once the vehicle is detected, click on Connect and then Unlock.

3. Go to EGS, Flash, Write Memory.

4. After you see computer information loaded click on continue.
*You might have popup saying that coding data needs to be saved. Click OK and wait a second. Next popup will tell you if backup for successful.
*If you get an ERROR warning, or a message saying that computer is not present in the system, then DO NOT continue. Contact us with your VIN so we can see what is the issue.

6. Click on Continue and then select Flash Option, depending on what is Available/Desired.

7. Now this is very important. Next steps start the flash process that takes about 5 minutes or so. During this time, you can’t turn of ignition, though it will cycle by itself. When you start the process, make sure to leave the driver door in the same position (if it was open, don’t close it. If its closed, don’t open it).

8. Click on start and wait until process finishes up.

9. After a successful flash, you should get a Pop-Up asking to clear DTC codes. Click Yes to all.

10. After your ignition cycles On and Off, you are done.




DME Flash To Full Stock or Recovery

Pre-Requisites
-Even though it’s not necessary, we recommend you hook up a battery charger for this process. Also park your vehicle in such a way that it doesn’t block your driveway/road in case of failed flash.
-Start the engine and let it idle. Turn lights off, radio off, heater/ac off. Pretty much turn all of the accessories to off position. Connect the eNet cable from your vehicle to laptop and make sure your laptop has WiFi connection.

Directions
1. Start the program and Click on Scan. You might have to click on scan few times if the program fails to detect your car.

2. Once the vehicle is detected, click on Connect and then Unlock.

3. Go to DME, Flash, Write Memory.

4. After you see computer information loaded click on continue.
*You might have popup saying that coding data needs to be saved. Click OK and wait a second. Next popup will tell you if backup for successful.
*If you get an ERROR warning, or a message saying that computer is not present in the system, then DO NOT continue. Contact us with your VIN so we can see what is the issue.

7. Go to settings (gear icon on the lower right), and select Emergency Recovery.

7. Click on Continue and then select Original. If you get a message asking if you want to keep your computer unlocked, select No.

8. Now this is very important. Next steps start the flash process that takes about 5 minutes or so. During this time, you can’t turn of ignition, though it will cycle by itself. When you start the process, make sure to leave the driver door in the same position (if it was open, don’t close it. If its closed, don’t open it).

9. Click on start and wait until process finishes up.

10. After a successful flash, you should get a Pop-Up asking to clear DTC codes. Click Yes to all.

11. After your ignition cycles On and Off, you are done.