04-05-2023, 05:08 PM | #1 |
New Member
3
Rep 27
Posts |
b58 cuts power when WOT?
Featured on BIMMERPOST.com |
04-06-2023, 11:07 AM | #4 |
Major General
4392
Rep 7,629
Posts |
Some might say so https://f30.bimmerpost.com/forums/sh....php?t=1732327
|
Appreciate
0
|
04-07-2023, 11:28 AM | #5 |
Captain
371
Rep 782
Posts |
Dollars to donuts your transmission is fucked! This is exactly what led me to getting a PDS transmission. If it's happening as you downshift into 3rd or 6th aggressively, it is def your issue.
To verify you'll need an actual scanner. BM3 wont do it. You'll need to log the transmission TURBINE SPEED to the OUTPUT SPEED sensors. Drive it while logging. Do the aggressive downshift. Pause the log and zoom in. Did the turbine speed drop by 50rpm as compared to output speed? If yes, replace the transmission. |
Appreciate
0
|
04-07-2023, 11:37 AM | #6 |
Lieutenant Colonel
1082
Rep 1,826
Posts |
For OP's sake I sure hope it's not a bad transmission. If it is though, would XHP maybe be the culprit? The ZF is pretty bullet proof from what people say hence why it's used in so many cars.
|
Appreciate
0
|
04-07-2023, 01:55 PM | #7 |
Major General
4392
Rep 7,629
Posts |
XHP doesn't cause transmission failures, especially with OTS tunes. If you start modifying things, using aggressive launch or other settings (which they warn about), then you could accelerate wear.
|
Appreciate
0
|
04-09-2023, 12:51 AM | #8 | |
New Member
3
Rep 27
Posts |
Quote:
|
|
Appreciate
0
|
04-09-2023, 10:26 PM | #9 |
Captain
654
Rep 604
Posts |
Upstream O2 sensor was the cause of similar problems on my f30.
__________________
|
Appreciate
0
|
04-10-2023, 06:42 PM | #11 | |
Major General
4392
Rep 7,629
Posts |
Quote:
No sure how you would theorize that the car would blow up due to a boost leak. It might cause excessively high WGDC but that's about it... you usually get air mass or other codes with a boost leak also, depending on the severity. |
|
Appreciate
1
Wires1664.50 |
04-10-2023, 10:08 PM | #12 |
New Member
3
Rep 27
Posts |
|
Appreciate
0
|
04-10-2023, 10:10 PM | #13 | |
New Member
3
Rep 27
Posts |
Quote:
|
|
Appreciate
0
|
04-11-2023, 05:07 PM | #14 | |
Major General
4392
Rep 7,629
Posts |
Quote:
|
|
Appreciate
0
|
04-11-2023, 07:30 PM | #15 |
New Member
3
Rep 27
Posts |
So yea I started I’m 3rd, took off and I think it was in either 4th or 5th gear where the power was cut, right after shifting.
|
Appreciate
0
|
04-11-2023, 07:37 PM | #16 | |
Major General
4392
Rep 7,629
Posts |
Quote:
EDIT: Just read that you have XHP stage 3. Check your XHP and MHD settings to make sure they are correct with respect to the torque limits. IIRC in MHD at least for N55 you need to tell it you have XHP. |
|
Appreciate
0
|
04-11-2023, 08:23 PM | #17 | |
New Member
3
Rep 27
Posts |
Quote:
|
|
Appreciate
0
|
04-11-2023, 10:32 PM | #18 |
Major General
4392
Rep 7,629
Posts |
|
Appreciate
0
|
04-11-2023, 10:42 PM | #19 |
New Member
3
Rep 27
Posts |
Yessir, there was a option on Mhd that removed TCU torque limiters, it says “not required for ots maps” but I still checked it and I just drove it hard for about an hour and it did well, hopefully that fixed the problem
|
Appreciate
0
|
04-19-2023, 12:10 PM | #20 |
New Member
3
Rep 27
Posts |
Here’s these two pulls, usually on my hp display it goes up to 560ish but with these it only went up to 480ish
https://datazap.me/u/meronshabba/low...og=0&data=3-19 https://datazap.me/u/meronshabba/low...og=0&data=3-19 I’d really appreciate it if y’all can help me out on these |
Appreciate
0
|
04-19-2023, 05:19 PM | #21 | |
Major General
4392
Rep 7,629
Posts |
Quote:
|
|
Appreciate
0
|
04-19-2023, 07:05 PM | #22 | |
New Member
3
Rep 27
Posts |
Quote:
https://datazap.me/u/meronshabba/4th...og=0&data=3-19 https://datazap.me/u/meronshabba/4th...og=0&data=3-19 |
|
Appreciate
0
|
Post Reply |
Bookmarks |
|
|