[lukas85]

Ok, I will try to disable transport mode. Thanks for help.

[lukas85]

Nope, no success. I connected ICOM, established connection with E-sys but nothing works.


Then I tried again with Ista+, I tried to diable Transport mode, but it didn't help. The ignition of the car can't be turned on/off. The dashboard turns on when I connect the car battery.








When I click "calculate measures plan", program just hangs, nothing works, I even left it for 20 minutes andnothing happened.


Any clues, maybye I'm doing something wrong or I really bricked ECU.

[atzebmw]

Originally Posted by lukas85

Nope, no success. I connected ICOM, established connection with E-sys but nothing works.

Did you ever work with E-Sys?
Do you get a connection to the car with E-Sys?

[lukas85]

Nope, I never worked with E-sys I selected connection to ICOM IP Address and I'm trying to read antyhing from the car to make sure it is working before programming. It is e-sys 3.30 with launcher pro 2.8.2 by tokenmaster.

[atzebmw]

Originally Posted by lukas85

Nope, I never worked with E-sys I selected connection to ICOM IP Address and I'm trying to read antyhing from the car to make sure it is working before programming. It is e-sys 3.30 with launcher pro 2.8.2 by tokenmaster.

Then try to connect by VIN.
Do you see the VIN of your car at the connection window?

[lukas85]

I have ENET cable but It somehow doesn't work. ICOM works ok on ISTA+, so I decided to connect to my car through tcp://169.254.92.38:50160 because that IP address is my ICOM device. ENET cable doesn't show under "ZGW" it is greyed out.


I believe that ICOM works with ista+ because ZGW module in my car was corrupted during flashing procedure. That's why ENET will not work.

If anyone is interested with helping me to programm DME or whatever is the problem I am willing to pay by paypal. We can use teamviewer for this purpose. Just contact me on pm.

[shawnsheridan]

Originally Posted by lukas85

Nope, no success. I connected ICOM, established connection with E-sys but nothing works.


Then I tried again with Ista+, I tried to diable Transport mode, but it didn't help. The ignition of the car can't be turned on/off. The dashboard turns on when I connect the car battery.

...
When I click "calculate measures plan", program just hangs, nothing works, I even left it for 20 minutes andnothing happened.

Any clues, maybye I'm doing something wrong or I really bricked ECU.

Originally Posted by lukas85

I have ENET cable but It somehow doesn't work. ICOM works ok on ISTA+, so I decided to connect to my car through tcp://169.254.92.38:50160 because that IP address is my ICOM device. ENET cable doesn't show under "ZGW" it is greyed out.

I believe that ICOM works with ista+ because ZGW module in my car was corrupted during flashing procedure. That's why ENET will not work.

If anyone is interested with helping me to programm DME or whatever is the problem I am willing to pay by paypal. We can use teamviewer for this purpose. Just contact me on pm.

If ICOM is working, Connect with ICOM and E-Sys, and use Read (ECU), not Read (SVT). If that works, look under DDE or DME Module, and see if CAFD is corrupted (cafd_ffffffff-255_255_255) or CAFD is missing.

[lukas85]

I'm not right know ath the car. I'll be there tomorrow. What I remember that when I clicked READ ECU the FA poped out but it was 0 (nothing in it).

I think I know wy e-sys is not properly communicationg with icom. I think I need to use "easy conneect utility" to change the bus of ICOM.

[shawnsheridan]

Originally Posted by lukas85

I'm not right know ath the car. I'll be there tomorrow. What I remember that when I clicked READ ECU the FA poped out but it was 0 (nothing in it).

I think I know wy e-sys is not properly communicationg with icom. I think I need to use "easy conneect utility" to change the bus of ICOM.

If ECU List is "0", your Conneciton is not correct.

Connection via ENET is a lot easier and simpler. You say it is not working because ZGW failed flash, but when you connected with ENET 1) Did you bypass E-Sys launcher and use E-Sys Direct? 2) Was MOTOR Running? 3) Did you disable All Windows Defender / Windows or any 3rd Party Firewall applications?

[lukas85]

1. No. I always run E-Sys with Launcher pro
2. No, I can't turn on the motor (start/stop doesn't work)
3. Yes windows defender and Firewall disabled, no third party apps.

[shawnsheridan]

Originally Posted by lukas85

1. No. I always run E-Sys with Launcher pro
2. No, I can't turn on the motor (start/stop doesn't work)
3. Yes windows defender and Firewall disabled, no third party apps.

Use E-Sys Launcher ONLY for FDL Coding, and nothing else. Bypass Launcher unless FDL Coding.

You need to put car on a Commercial Grade 50+ Amp Charger, or jump car to another car with its Motor Running.

ENET Cable should work, unless you have bad ENET Cable.

[lukas85]

Ok, I will definitely do that tomorrow, without launcher.

Can anyone tell me how to set up ICOM A2 (clone) with itoollradar to properly communicate with E-sys ?

[shawnsheridan]

Originally Posted by lukas85

Ok, I will definitely do that tomorrow, without launcher.

Can anyone tell me how to set up ICOM A2 (clone) with itoollradar to properly communicate with E-sys ?

Open iTool
Note xxx.xxx.xxx.xxx IP Address of ICOM
Hit Reserve Button to Lock ICOM

Open E-SYS
Click the connection icon
Select the car model
Select type of connection: "Connection via ICOM / Ethernet:" and put in box = tcp :/ / xxx.xxx.xxx.xxx:50160

[lukas85]

Success !! E-sys finaly connected, I reprogrammed FEM module and car is now turning on/off everything works !

@shawnsheridan thank you for your support !!

[shawnsheridan]

Originally Posted by lukas85

Success !! E-sys finaly connected, I reprogrammed FEM module and car is now turning on/off everything works !

@shawnsheridan thank you for your support !!

[lukas85]

There is one more thing left. I need to enable "angel eyes". Left lamp was replaced in my F30 2018 and angel eyes works only only on that left lamp. Which "coding" I need to change in order to enable "angel eyes" on right one. Also blinkers doesn't work on both of these lamps.



I believe these are called sidemarkers not angel eyes, I'm not sure. :P

[shawnsheridan]

Originally Posted by lukas85

There is one more thing left. I need to enable "angel eyes". Left lamp was replaced in my F30 2018 and angel eyes works only only on that left lamp. Which "coding" I need to change in order to enable "angel eyes" on right one. Also blinkers doesn't work on both of these lamps.



I believe these are called sidemarkers not angel eyes, I'm not sure. :P

If light was replaced with same light, VO Code FEM Module and Light Modules (e.g. TMS, FLE, etc.).

[lukas85]

Sorry I don't follow. I believe that my 2018 car is LCI and FME_Body no longer controls the lights, right ?

So which module tree should I modify ?

[shawnsheridan]

Originally Posted by lukas85

Sorry I don't follow. I believe that my 2018 car is LCI and FME_Body no longer controls the lights, right ?

So which module tree should I modify ?

Do as I wrote. VO Code FEM and individual Light Modules.

[lukas85]

Can anyone send me a sort of tutorial how to VO Code FEM ? I'm like blind in the dark here

[shawnsheridan]

Originally Posted by lukas85

Can anyone send me a sort of tutorial how to VO Code FEM ? I'm like blind in the dark here

VO Code:

Connect => Read FA (VO) => Activate FA (VO) => Read (ECU) => Right-Click on FEM_BODY (the ECU itself not the underlying CAFD) => Select CODE.

[lukas85]

Thank you for that clear instructions !

You also said individual light modules. How can I check which module is for lights ? Is there any kind of cheat sheet for that?