07-27-2022, 12:46 PM | #23 |
Lieutenant
396
Rep 432
Posts |
Video from a rainy day with the PCA. Took my 2013 F30 to the track and we had a blast passing all day long. Not a single point bye. Intermediate Group.
Enjoy!
__________________
Quietly Effective
|
Appreciate
3
|
07-31-2022, 11:45 AM | #24 |
Brigadier General
12449
Rep 3,434
Posts |
|
07-31-2022, 10:07 PM | #25 |
Lieutenant
396
Rep 432
Posts |
Stock F30 with PS4S tires. The equalizer was the rain. And maybe that I've done a number of track days in rain, not to mention my hardware isn't nearly as costly so running balls out wasn't so scary.
Tracking in the rain is a blast. Don't let a rainy day keep you away. I've owned a couple of P-Cars. Our local PCA puts on some great events.
__________________
Quietly Effective
|
Appreciate
2
MacklinUSOB519.00 FlorinQCK-2.50 |
08-01-2022, 08:39 PM | #26 | |
Captain
519
Rep 891
Posts |
Quote:
I had a set of PS4S on the car in, first thing I changed on it, actually. They kicked off my suspension rabbit hole. Living in an apartment I had to run RS4 for drive on/off (NYC). Inferior to the PS4S in the wet, no doubt, but more manageable than the other 200TWs.
__________________
328i RWD | MW on CRed Slick Top | 6MT | BM3 | MPE | GPlus FMIC | CSF Radiator | Millway Street Camber Plates & Monoballs | KW V2 6k/18k Swift Springs | F80 LCA/TS | SPL Bump Steer Kit | APEX SM-10 | R-S4 | DS2500 | RBF600 | SS Lines | Past: E36 328is & E38 740i |
|
08-02-2022, 09:27 AM | #28 | |
Captain
519
Rep 891
Posts |
Quote:
Camber is what really changes the game, though. There are even some OEM options for that as well if you want less of a project.
__________________
328i RWD | MW on CRed Slick Top | 6MT | BM3 | MPE | GPlus FMIC | CSF Radiator | Millway Street Camber Plates & Monoballs | KW V2 6k/18k Swift Springs | F80 LCA/TS | SPL Bump Steer Kit | APEX SM-10 | R-S4 | DS2500 | RBF600 | SS Lines | Past: E36 328is & E38 740i |
|
Appreciate
1
FlorinQCK-2.50 |
08-02-2022, 11:53 AM | #29 | |
Banned
270
Rep 665
Posts |
Quote:
as for camber, what is the right setup? should i buy the camber plate as well? |
|
Appreciate
2
MacklinUSOB519.00 FlorinQCK-2.50 |
08-02-2022, 01:20 PM | #30 | |
Captain
519
Rep 891
Posts |
Quote:
If I were to suggest 2 mods alongside a front suspension refresh it would be the Millway Street Camber Plates and the Millway Street thrust arm/tension strut monoballs. Both add very little NVH which is great for a daily, but you get the benefits of camber adjustment on top of the reduced deflection on the thrust arm. I have been running -3/-2 for a while and it has a great balance. Toe you can leave stock, or start getting closer to neutral on the front end. For a more streetable alignment -2/-1.5~ with stock toe raises the limit quite a lot without going too crazy. https://www.millway.se/camber-plates...0-f31-f32.html https://www.millway.se/front-control...w-f20-f30.html
__________________
328i RWD | MW on CRed Slick Top | 6MT | BM3 | MPE | GPlus FMIC | CSF Radiator | Millway Street Camber Plates & Monoballs | KW V2 6k/18k Swift Springs | F80 LCA/TS | SPL Bump Steer Kit | APEX SM-10 | R-S4 | DS2500 | RBF600 | SS Lines | Past: E36 328is & E38 740i |
|
08-02-2022, 01:39 PM | #31 | |
Banned
270
Rep 665
Posts |
damn, everyone on the forum suggest the monoballs, the options are either VAC monoball or millway monoball. i guess i m probably going to get the VAC monoball because it's already pressed in, and just simple removing and install.
the monoball itself is cheaper by its own, but looking at 7 years old age, changing the arm is not a bad idea, i would think... so it can go another 7 years. how about rear suspension? no need to refresh them? Quote:
|
|
Appreciate
1
FlorinQCK-2.50 |
08-02-2022, 03:01 PM | #32 | |
Captain
519
Rep 891
Posts |
Quote:
https://www.millway.se/front-tension...lemforder.html As for the rear suspension, it typically gets less wear than the front. I am still on stock hardware for the most part on my 2012 and it's still tight and holds alignment well. You could replace the struts, they are pretty easy and inexpensive.
__________________
328i RWD | MW on CRed Slick Top | 6MT | BM3 | MPE | GPlus FMIC | CSF Radiator | Millway Street Camber Plates & Monoballs | KW V2 6k/18k Swift Springs | F80 LCA/TS | SPL Bump Steer Kit | APEX SM-10 | R-S4 | DS2500 | RBF600 | SS Lines | Past: E36 328is & E38 740i |
|
Appreciate
1
FlorinQCK-2.50 |
08-04-2022, 07:05 PM | #33 |
Check out my Youtube @n55david!
1318
Rep 3,593
Posts
Drives: 2017 m240i, 2015 X3 x35i
Join Date: Aug 2018
Location: Michigan USA
|
I'm just here for the dodge hate.. I love it
Yeah IC is a must even on a stock car etc
__________________
2017 m240i xDrive 10.67@132.32mph w/bm3
2015 335i xDrive 10.95@124.99mph w/bm3 - SOLD 2015 X3 x35i pwg 12.96 catless w/bm3 stage 2 93 ots IG: @n55david For pics and updates! Youtube: @ n55david For videos or Racing etc |
Appreciate
2
MacklinUSOB519.00 FlorinQCK-2.50 |
Post Reply |
Bookmarks |
|
|