[Djbigboss]

Previous owner probably made wrong software on it, it also no longer works usb only sd card.

By the way, it's a snapdragon 450 I've read now.

[Maen999]

Originally Posted by rytec

This morning when I started the car it gave me this screen of the oem.
it was now in the middle of the Android HU instead of the left side.
And I did not change anything since I left it yesterday as it was, and below also the actual display config how it is now.

What should I do now?

Hello I have the same issue how did you solve it

[Kamsung]

Hey. I've installed a junsun android unit in my f30. Green cables connected. Sounds comes fine through speakers. However when I call or receive a call I cannot hear the person on the other side. They can hear me. Removed my Bluetooth device from the nbt so it can't connect. Even if I don't use the android car play and use bluetooth only through the headunit same issue. Also my settings don't save after each time I start the car of the headunit. Not sure if thats related.

Any ideas?

Thanks

[coathangers]

I have the 12 inch touchscreen version of this android head unit in my F48 X1 and it is working. I have a MASSIVE problem in that every time I do a stop start or navigate to the OEM system then the android audio that is playing is muted until I reopen the app.

I have the unit going into the aux port of the HU ENTRYNAV system.

I asked the icodebmw guys for help and they have never come across this problem before.

So annoying I will have to remove the whole system if I can't get it fixed as I am constantly touching the screen while driving to open YouTube music or Waze

Has someone had this problem or know how to fix it?

[DenGli]

Originally Posted by coathangers

...to the OEM system then the android audio that is playing is muted until I reopen the app...

Hello!

The following software will help solve your problem:
KSW-ToolKit

[alexlory]

Hi my name is Alex, I have a Audi Q7 3.0 tdi year 2012 with MMI3g basic and
I have new audio and video system with
MSM8953EA_M501_Q_20200519.1
Ksw-Q-Userdebug_OS_v2.6.3
is possible update my system and wich vertion is possible to install
thx
Alex

[DenGli]

Originally Posted by alexlory

is possible update my system and wich vertion is possible to install

Greetings.
Initially, you need to check the native version of Android on HU.
Identify Native Headunits

After that, if you have native Android 10, you can update to the latest version - 4.2.9.
It might be better to do a clean update, instructions are available at the link above.

[coathangers]

Originally Posted by DenGli

Hello!

The following software will help solve your problem:
KSW-ToolKit

Yes! Thank you this app is perfect, wish the distributor would just tell me about this.

You saved me a lot of time and money !

[RedErik]

Originally Posted by coathangers

Yes! Thank you this app is perfect, wish the distributor would just tell me about this.

You saved me a lot of time and money !

Why would they? It's a community made app and has nothing to do with Chinese devs. Snaggle spent months working on it and reverse engineering Chinese firmware... and still is actively working on updates, new features and compatibility with new hardware.

[inceselcuk974]

Originally Posted by RedErik

Interesting... so looks like F10 (NBT?) MCU is completely different in that aspect. Mine just switches off 2sec after I shift to D and PDC sensors are still making noise, PDC button is lit up, but Android is no longer showing PDC screen. I recorded a video comparing both Android and OEM behaviour, sent that over to Andream and all I got in return was that message say "this is normal".

Hello, could you solve the problem by wiring, i have exactly the same problem with my android headunit, bmw f30 3.18 2015….when i shift to d, it returns to android part

[inceselcuk974]

Originally Posted by koutsouk

You can solve it by connecting the cable for camera enable signal to the 12v of your pdc module.
With that the system will think that you still have reverse gear and will be on till the PDC shuts off.
Maybe after that you must enable the aftermarket camera to function correctly.
I had this configuration with my old 8.1 unit and was working flawlessly.
I do not know if the system is different in Android 10 but give it a try, it needs some wiring but you can achieve what you want without software upgrade.

Hello how can we connect enable signal cable to pdc module? in the trunk area? where is the pdc module in the car? thanks

[RedErik]

Originally Posted by inceselcuk974

Hello, could you solve the problem by wiring, i have exactly the same problem with my android headunit, bmw f30 3.18 2015….when i shift to d, it returns to android part

You probably could, but you need to figure out where you want to tap in (PDC button, PDC module, reverse light) and how to properly do it. I'm no longer using Android in my car so I don't have that problem.

[GNA]

Ciao Bimmer,

I have a question about my head unit by Xtrons.
I would like update it with a new software mine is:
MCU ver 0230052dGS-C&C-GTL-210825-B18
App vers: Ksw-Q-Userdebug_OS_v3.2.2
Os Ver: 10-501A-EA-1-868927050410096.

If I'm not wrong I can update mcu and software daowlòoading on first topic page.

Is it right?

My other quetion is what is the best setup un vehicle menu, mine is a X1 e84 without monitor.

I don't know what are the differences between these values:
Aux switcing modes
Aux auto swithing
knob type
driver's seat
number of doors
Gear selection
mode key selection
Voice key selection
collect can bus data
stewring wheel track selection

thanks a lot to who will reply to m,y questions!

REgards
Matteo

[Someoneelse]

everything you ask about is described in detail in posts 1 and 2 of this thread, or https://kamilbrk.github.io/headunits/ It's hard to find more information anywhere else

[GNA]

Ciao
I red all post into this 3d, but I have a doubt
what software I need to download?

I found this:
Ksw-Q-Userdebug_OS_v4.2.9-ota (A10) 25-12-2023 that is the last, but I red als this:
For Latest OTA Firmware version NativeAndroid10 Units ( 3.1.6+ ): check " HERE

So what I need to download for my radio?

thanks a lot.
Matteo

[Tom Jonkman]

Hey everyone!

Just signed in because you are my last hope in search of an answer! I currently have a BMW F30 316i from 2013 with a android headunit build in. I've got the:

MCU ver: 023052dGS-NBT-GTH-190816-B18
APP ver: Ksw-P-Userdebug_OS_v2.4.5
System version: 9.0
RAM: 4G

Recently my bluetooth isn't working properly anymore.. I would love to know how I can upgrade my system so everything will be working again. Also i would like to know if there is an option to use Carplay on my headunit.

If anyone can help me out with what to do and where to find it please reach out

Hope to hear from you guys soon!

[RedErik]

Originally Posted by GNA

Ciao
I red all post into this 3d, but I have a doubt
what software I need to download?

I found this:
Ksw-Q-Userdebug_OS_v4.2.9-ota (A10) 25-12-2023 that is the last, but I red als this:
For Latest OTA Firmware version NativeAndroid10 Units ( 3.1.6+ ): check " HERE

So what I need to download for my radio?

thanks a lot.
Matteo

You are already on 3.2.2, so already past that 3.1.5... don't understand what's so confusing.

[GNA]

Originally Posted by RedErik

You are already on 3.2.2, so already past that 3.1.5... don't understand what's so confusing.

Can I pass to a new version?

https://kamilbrk.github.io/headunits/updates/ksw/
here there are other version after 3.2.2 or not?

thanks a lot
Matteo

[RedErik]

Originally Posted by GNA

Can I pass to a new version?

https://kamilbrk.github.io/headunits/updates/ksw/
here there are other version after 3.2.2 or not?

thanks a lot
Matteo

Yes, there are other version after 3.2.2... still don't understand what's confusing about that.

[GNA]

I'n not confusing, I'm only asking what version advise to install

Can I install directly the last -> Ksw-Q-Userdebug_OS_v4.2.9-ota

M501 (SD625/MSM8953)
Ksw-Q-Userdebug_OS_v4.2.9-ota (A10) 2023-12-25
Ksw-Q-Userdebug_OS_v4.2.0-ota (A10) 2023-09-08
Ksw-Q-Userdebug_OS_v4.1.6-ota (A10) 2023-07-17
Ksw-Q-Userdebug_OS_v4.0.7-ota (A10) 2023-03-23
Ksw-Q-Userdebug_OS_v4.0.4-ota (A10) 2023-03-02
Ksw-Q-Userdebug_OS_v3.9.6-ota (A10) 2022-12-16
Ksw-Q-Userdebug_OS_v3.9.4-ota (A10) 2022-11-24
Ksw-Q-Userdebug_OS_v3.9.1-ota (A10) 2022-10-24
Ksw-Q-Userdebug_OS_v3.8.9-ota (A10) 2022-09-13

or for my radio it will be better another one?

thanks a lot
Matteo

[RedErik]

Originally Posted by GNA

I'n not confusing, I'm only asking what version advise to install

Can I install directly the last -> Ksw-Q-Userdebug_OS_v4.2.9-ota

M501 (SD625/MSM8953)
Ksw-Q-Userdebug_OS_v4.2.9-ota (A10) 2023-12-25
Ksw-Q-Userdebug_OS_v4.2.0-ota (A10) 2023-09-08
Ksw-Q-Userdebug_OS_v4.1.6-ota (A10) 2023-07-17
Ksw-Q-Userdebug_OS_v4.0.7-ota (A10) 2023-03-23
Ksw-Q-Userdebug_OS_v4.0.4-ota (A10) 2023-03-02
Ksw-Q-Userdebug_OS_v3.9.6-ota (A10) 2022-12-16
Ksw-Q-Userdebug_OS_v3.9.4-ota (A10) 2022-11-24
Ksw-Q-Userdebug_OS_v3.9.1-ota (A10) 2022-10-24
Ksw-Q-Userdebug_OS_v3.8.9-ota (A10) 2022-09-13

or for my radio it will be better another one?

thanks a lot
Matteo

Any? Just try one after another and see if that fixes your problem, whatever that is.

[GNA]

ok, I would like to be sure to install the right one, so you suggest to install 3.8.9 before and go on with the other, right?

I don't know If some one update le same radio and can tell me some advise :-)

thanks
Matteo