01-16-2014, 11:48 PM | #111 |
First Lieutenant
60
Rep 378
Posts |
|
Appreciate
0
|
01-17-2014, 01:54 PM | #112 | |
Registered
0
Rep 2
Posts |
Quote:
Would it be possible to buy the male and female ends of the harness and create an adapter that would allow for complete adaption/removal? Similar to A4 xeon retrofit via Kufatec adapter? Last edited by F30_rdc; 01-17-2014 at 02:00 PM.. |
|
Appreciate
0
|
01-17-2014, 02:36 PM | #113 | |
First Lieutenant
60
Rep 378
Posts |
Quote:
That being said, I just added the steps for wiring the FEM module now. I will try and work on the DIY more later, but I need to do some work for now. Feel free to comment about the progress and ask questions for the sections I already completed. https://docs.google.com/document/d/1...it?usp=sharing |
|
Appreciate
0
|
01-17-2014, 04:20 PM | #114 |
Private
8
Rep 54
Posts |
Hello,
I retrofited xenon (wo ahl 522) on my 320i, I study the wiring, and i am totally okay with the first topic I ordered sensor for levering LWR, not yet installed. I did the coding $522 with e-sys, and xenon works fine, bi-xenon shutter okay. There is a but, i did a look with Inpa for errors : Code:
x8041B6 headlight range control (LWR ): System failed Error counter : 1 Healing counter : 40 ***Absolute time 48084805 s ***Mileage 19210 km ***SPANNUNG_BORDNETZ 13.70 V ***KLEMMEN_STATUS : KL15 - A 1.000000E +001 0-n ***SPANNUNG_TMS 0:00 V ***Fulfills test conditions ***Error currently available and already stored ***Error would not cause illumination of a warning lamp ***This is no event DTC. This ecu IS RESPONSIBLE for this error entry. Error code : 80 41 0F B6 01 05 17 00 00 4B 17 0A 01 02 DD B7 ************45 40 40 89 40 41 0A 40 48 00 80 41 0F B6 01 00 ************02 01 03 28 -------------------------------------------------- ----------- 0xD90C10 LIN Master Q: No communication Error counter : 1 Healing counter : 40 ***Absolute time 48084805 s ***Mileage 19210 km ***Fulfills test conditions ***Error currently available and already stored ***Error would not cause illumination of a warning lamp ***This is no event DTC. This ecu IS RESPONSIBLE for this error entry. Error code : D9 0C 10 0F 01 02 17 00 00 4B 17 0A 01 02 DD B7 ************D9 45 0C 10 0F 01 00 02 01 03 28 -------------------------------------------------- ----------- 0xD90D16 operating unit light (BEL ), ( LIN): wrong version installed Error counter : 1 Healing counter : 255 ***Absolute time 48084805 s ***Mileage 19210 km ***Expected Node Variant 09 HEX ***Variant of LIN slave node 0b HEX ***LIN node access 28 HEX ***Fulfills test conditions ***Error currently available and already stored ***Error would not cause illumination of a warning lamp ***This is no event DTC. This ecu IS RESPONSIBLE for this error entry. Error code : D9 0D 16 0F 01 05 17 00 00 4B 17 0A 01 02 DD B7 ************45 40 B2 09 40 B3 40 B4 28 D9 0B 0D 16 0F 01 00 ************02 01 03 FF but this error : 0xD90D16 operating unit light (BEL ), ( LIN): wrong version installed This error is very strange, I hope that we do need to change FEM in order to make xenon working correctly ! What i do, i updated FEM with 50.4 data, i see all paramter about LWR, AHL... but the error still there. FYI, i correctly swap wires on FEM for pin 8 ( lin ******ion). |
Appreciate
0
|
01-18-2014, 10:18 AM | #115 |
Private
8
Rep 54
Posts |
|
Appreciate
0
|
01-19-2014, 07:25 PM | #116 |
First Lieutenant
60
Rep 378
Posts |
Hey guys, I just added in the front level sensor install. I still have to finish the headlight removal and install (waiting on more pictures) and the rear level sensor install. Other than that just some touching up and should be complete. I will try and do a little each day.
Is everyone finding this helpful? Please feel free to ask questions and make suggestions. Once it is complete I will start a new thread as I cannot edit the OP's first post to add the DIY to there. |
Appreciate
0
|
01-19-2014, 07:51 PM | #117 | |
Private
6
Rep 88
Posts |
Quote:
I'd request you add what needs to be coded though. I'm not asking how to code, but at least what needs to be added, FDL coded...etc. And thanks for the document. Can't wait for the complete guide |
|
Appreciate
0
|
01-19-2014, 10:41 PM | #118 | |
First Lieutenant
60
Rep 378
Posts |
Quote:
|
|
Appreciate
0
|
01-20-2014, 05:01 PM | #120 |
Private
6
Rep 88
Posts |
Did you mean LWL_AHL_TYP? There's no AHL_TYP in FEM. Also, it looks like setting C_BLC_ENA = F030disable is more appropriate.
@kapkanimd, what does the auto-leveler do? Is it for the vertical orientation/adjustment? You mentioned cornering works in your document. Does this mean the lamp adjust constantly in relation to the road/steering position? |
Appreciate
0
|
01-20-2014, 05:06 PM | #121 | |
First Lieutenant
60
Rep 378
Posts |
Quote:
|
|
Appreciate
0
|
01-21-2014, 04:51 PM | #123 | |
Private
8
Rep 54
Posts |
Quote:
|
|
Appreciate
0
|
01-23-2014, 06:08 PM | #124 |
First Lieutenant
60
Rep 378
Posts |
Corrected the part number, thanks F30EDR. Also I just added installing the rear sensor. I didn't finish the wiring yet, but will do so when I can. Other than that, it shouldn't be too long till finished.
|
Appreciate
0
|
01-24-2014, 11:43 AM | #125 |
Private
8
Rep 54
Posts |
|
Appreciate
0
|
01-24-2014, 12:22 PM | #126 |
First Lieutenant
60
Rep 378
Posts |
Everything is now complete except for the headlight removal and reinstall. I am still waiting on a few more pictures and I will update when I can. Other than that I finished the auto level install. Enjoy.
Again, let me know if there are any questions or clarification needed or if you need the pictures enlarged or more pictures. |
Appreciate
0
|
01-30-2014, 09:03 PM | #127 |
Private
6
Rep 88
Posts |
Did you get the levelers working?
All the parts I've ordered are coming in tomorrow. Controllers are ridiculously expensive and I still can't believe I shelled out that much for 2 pieces of circuit boards. I'm out $1200, excluding the housing. A little bit over 2 grand for everything. I'm sure it will be worth it once installed and I see it working. |
Appreciate
0
|
01-30-2014, 10:45 PM | #128 | |
First Lieutenant
60
Rep 378
Posts |
Quote:
seems like you didn't want to be patient... I got the circuit boards for about $165 each... you will definitely appreciate them though once they are in did you order just the headlights or the leveling sensors as well? |
|
Appreciate
0
|
01-30-2014, 10:58 PM | #129 |
Private
6
Rep 88
Posts |
That is a good price. I paid $295 a pop and I thought that was a good price already, considering they go for $375 elsewhere. I just got tired of waiting for them to show up in eBay after 2 weeks of everyday checking.
I'm doing just the headlights for now, I may add the leveling sensors later. |
Appreciate
0
|
01-30-2014, 11:05 PM | #130 | |
First Lieutenant
60
Rep 378
Posts |
Quote:
Sounds good, and good luck. I was trying to make a sticky for my DIY as it applies to US spec only cars (for the most part) and keep it a little separate and cleaner than this thread which is also a great reference. If you complete it or have any questions that will be of benefit for the DIY please post in this thread: http://www.f30post.com/forums/showthread.php?t=938803 Also, if you could, please take pictures of the headlights after the bumper is removed to show locations of bottom screws and path to remove them. I just forgot and it would help make the DIY a little more complete. Last edited by kapkanimd; 01-30-2014 at 11:23 PM.. |
|
Appreciate
0
|
01-30-2014, 11:49 PM | #131 |
Private
6
Rep 88
Posts |
I'll keep this in mind.
I'm debating whether to start the retrofit in 2 weeks or wait till after I bring my car in for service early March. I want them to update the software and don't want anything interfering with that. |
Appreciate
0
|
02-01-2014, 02:27 PM | #132 |
Private
8
Rep 54
Posts |
I did the installation of the two levels sensor wired to the ICM, no more error from ICM, we can monitor value with INPA.
Now, i have error from the FEM, , FEM cannot give the correct position of the headlight, it seems that it is an issue with the LIN.. i do not undestand, i correctly wired the LIN bus to the FEM: i will check again the wiring ! I tryed to calibrate sensor with inpa, but calibration failed due to bad value from FEM... So maybe my headlight module are defect... Last edited by mougwai; 02-01-2014 at 02:43 PM.. |
Appreciate
0
|
Post Reply |
Bookmarks |
|
|