Is it possible to clear check engine codes with Esys / an ENET cable?

azwillnj · 08-16-2013, 05:08 PM

I coded some stuff in the Kombi box and triggered a check engine light somehow, the car is running fine. Is there a way with the ENET cable to to check the codes and clear them?

HFW003 · 08-16-2013, 05:40 PM

You can try Tool32 and with thanks to Shawnsheridan, this is how you do it.

There are two versions of Tool32 in EDIABAS so make sure you use the German version as the English one won't work.

Assuming the fault condition no longer exists, to clear the fault code.

1) Launch C:\EDIABAS\Bin\TOOL32.EXE
2) Hit F3
3) Load C:\EDIABAS\Ecu\F01.PRG
4) In the "Select Job: F01" window, select FS_LOESCHEN_FUNKTIONAL
5) Hit F5
6) "Results" window should show "JOB_STATUS = OKAY"

Hopefully, Problem Solved.
Note: fs_lesen_funktional only read fault codes, FS_LOESCHEN_FUNKTIONAL will delete it.

Good luck

H

azwillnj · 08-16-2013, 10:03 PM

That worked perfectly, thanks so much!

Quote:

Originally Posted by HFW003

You can try Tool32 and with thanks to Shawnsheridan, this is how you do it.

There are two versions of Tool32 in EDIABAS so make sure you use the German version as the English one won't work.

Assuming the fault condition no longer exists, to clear the fault code.

1) Launch C:\EDIABAS\Bin\TOOL32.EXE
2) Hit F3
3) Load C:\EDIABAS\Ecu\F01.PRG
4) In the "Select Job: F01" window, select FS_LOESCHEN_FUNKTIONAL
5) Hit F5
6) "Results" window should show "JOB_STATUS = OKAY"

Hopefully, Problem Solved.
Note: fs_lesen_funktional only read fault codes, FS_LOESCHEN_FUNKTIONAL will delete it.

Good luck

H

HFW003 · 08-16-2013, 10:06 PM

You're welcome!

mocohead · 08-17-2013, 12:52 PM

Let's chat about this a bit further as I was wondering the same thing.

Recently I had a bad experience after changing my spark plugs. The car was in limp mode, CEL on, and it would not start at all. There were TONS of codes stored when the car got to the dealer.

But I ran Tool32, all of the steps described above, and it did not find ANY codes. Thoughts?

shawnsheridan · 08-17-2013, 09:10 PM

Quote:

Originally Posted by HFW003

You can try Tool32 and with thanks to Shawnsheridan, this is how you do it.

There are two versions of Tool32 in EDIABAS so make sure you use the German version as the English one won't work.

Assuming the fault condition no longer exists, to clear the fault code.

1) Launch C:\EDIABAS\Bin\TOOL32.EXE
2) Hit F3
3) Load C:\EDIABAS\Ecu\F01.PRG
4) In the "Select Job: F01" window, select FS_LOESCHEN_FUNKTIONAL
5) Hit F5
6) "Results" window should show "JOB_STATUS = OKAY"

Hopefully, Problem Solved.
Note: fs_lesen_funktional only read fault codes, FS_LOESCHEN_FUNKTIONAL will delete it.

Good luck

H

rdubmd · 09-08-2013, 09:07 PM

When I try to load the prg file the program just hangs... and if I click stuff I get different errors of OCX files missing, but they are in the folder... any thoughts?

Thanks,

Quote:

Originally Posted by HFW003

You can try Tool32 and with thanks to Shawnsheridan, this is how you do it.

There are two versions of Tool32 in EDIABAS so make sure you use the German version as the English one won't work.

Assuming the fault condition no longer exists, to clear the fault code.

1) Launch C:\EDIABAS\Bin\TOOL32.EXE
2) Hit F3
3) Load C:\EDIABAS\Ecu\F01.PRG
4) In the "Select Job: F01" window, select FS_LOESCHEN_FUNKTIONAL
5) Hit F5
6) "Results" window should show "JOB_STATUS = OKAY"

Hopefully, Problem Solved.
Note: fs_lesen_funktional only read fault codes, FS_LOESCHEN_FUNKTIONAL will delete it.

Good luck

H

shawnsheridan · 09-08-2013, 09:30 PM

Quote:

Originally Posted by rdubmd

When I try to load the prg file the program just hangs... and if I click stuff I get different errors of OCX files missing, but they are in the folder... any thoughts?

Thanks,

Is your EDIABIS.ini file set for ENET Interface?

Are you connected to the car, with power on the car when you try it?

HFW003 · 09-08-2013, 09:42 PM

Quote:

Originally Posted by rdubmd

When I try to load the prg file the program just hangs... and if I click stuff I get different errors of OCX files missing, but they are in the folder... any thoughts?

Thanks,

You need to use the German version not the one in English!

H

navy.doc · 12-19-2013, 09:51 AM

I'm trying to use Tool32, but I think I have the English version, not the german how i can get the german version. Thanks

HFW003 · 12-19-2013, 02:43 PM

If you, like many other, have received the coding package from Shawn then it is in there. You just need to search for it.

navy.doc · 12-20-2013, 03:00 PM

Quote:

Originally Posted by rdubmd

When I try to load the prg file the program just hangs... and if I click stuff I get different errors of OCX files missing, but they are in the folder... any thoughts?

Thanks,

What worked for me after reading for a while is to copy to C:\Windows\SysWOW64 the following files "MSLFXGRD.OCX" and "Richtx32.ocx" from C:\EDIABAS\Bin and register the using Command Prompt as an Administrator with the following command regsvr32 C:\Windows\SysWOW64\MSLFXGRD.OCX and regsvr32 C:\Windows\SysWOW64\Richtx32.ocx. I think this problem only happens in computer running 64bits. Hope that helps

vitchie · 01-14-2014, 03:17 AM

Hi guys, I got the coding pack, but not sure where the german version of tool 32 is? There is only 1 tool32 in bin?

HFW003 · 01-14-2014, 04:07 AM

I'm not sure what Shawn now sends out mate. Just try the one and see if it works. If it's not the correct one you will notice it just hangs when you try to use it.

vitchie · 01-14-2014, 04:17 AM

Ok, figured it out. Had to run it as administrator.

joeaye · 01-14-2014, 10:42 PM

I had the same issue with Tool32, I needed to run it on windows pro because it was 32bit and my machine only ran 64bit (or windows xp/vista). I tested this on a few computers too and that was the common denominator.

steddyman · 01-15-2014, 01:59 AM

I found when VO coding the KOMBI it reset the date and time. This causes the warning triangle to appear and setting it correct on the iDrive clears it.

nyc_king · 03-21-2014, 07:30 PM

Quote:

Originally Posted by HFW003

You can try Tool32 and with thanks to Shawnsheridan, this is how you do it.

There are two versions of Tool32 in EDIABAS so make sure you use the German version as the English one won't work.

Assuming the fault condition no longer exists, to clear the fault code.

1) Launch C:\EDIABAS\Bin\TOOL32.EXE
2) Hit F3
3) Load C:\EDIABAS\Ecu\F01.PRG
4) In the "Select Job: F01" window, select FS_LOESCHEN_FUNKTIONAL
5) Hit F5
6) "Results" window should show "JOB_STATUS = OKAY"

Hopefully, Problem Solved.
Note: fs_lesen_funktional only read fault codes, FS_LOESCHEN_FUNKTIONAL will delete it.

Good luck

H

Hi, So this happened to me as well but I am running E-sys 3.24.3 and there is no EDIABAS folder. Is there another way to clear this with E-Sys?

shawnsheridan · 03-22-2014, 12:06 AM

Quote:

Originally Posted by nyc_king

Hi, So this happened to me as well but I am running E-sys 3.24.3 and there is no EDIABAS folder. Is there another way to clear this with E-Sys?

EDIABAS is no longer included in E-Sys package as it is not required by E-Sys.

PM sent.

BooGooBird · 03-29-2014, 04:12 PM

Quote:

Originally Posted by shawnsheridan

EDIABAS is no longer included in E-Sys package as it is not required by E-Sys.

PM sent.

Can I also get the link for EDIABAS? Just got check engine light on after coded disable LED bulb check...

Thanks Shawn

shawnsheridan · 03-29-2014, 05:18 PM

Quote:

Originally Posted by lebroncj

Can I also get the link for EDIABAS? Just got check engine light on after coded disable LED bulb check...

Thanks Shawn

PM sent.

F30_NY91 · 06-02-2014, 04:55 PM

Hi Shawn

I have an engine code also. Do you have the latest tool32?

08-16-2013, 05:08 PM	#1
azwillnj First Lieutenant 118 Rep 324 Posts Drives: 2013 F30 328i xDrive Join Date: Nov 2007 Location: Northern VA iTrader: (0)	Is it possible to clear check engine codes with Esys / an ENET cable? I coded some stuff in the Kombi box and triggered a check engine light somehow, the car is running fine. Is there a way with the ENET cable to to check the codes and clear them? __________________ Current: 2020 M340i xDrive - DAP - DAP Pro - Prem - Executive - Remote Start - Wireless Charging - HK History: 2008 e90 328xi > 2011 e90 LCI 335i xDrive > 2013 F30 328i xDrive > 2016 F30 LCI 340i xDrive WE ARE!
	Appreciate 1 Tweet Quote

08-16-2013, 05:40 PM	#2
HFW003 Colonel 1905 Rep 2,673 Posts Drives: MY19 LBB M2 Comp Join Date: Apr 2013 Location: Newcastle, Australia iTrader: (0)	You can try Tool32 and with thanks to Shawnsheridan, this is how you do it. There are two versions of Tool32 in EDIABAS so make sure you use the German version as the English one won't work. Assuming the fault condition no longer exists, to clear the fault code. 1) Launch C:\EDIABAS\Bin\TOOL32.EXE 2) Hit F3 3) Load C:\EDIABAS\Ecu\F01.PRG 4) In the "Select Job: F01" window, select FS_LOESCHEN_FUNKTIONAL 5) Hit F5 6) "Results" window should show "JOB_STATUS = OKAY" Hopefully, Problem Solved. Note: fs_lesen_funktional only read fault codes, FS_LOESCHEN_FUNKTIONAL will delete it. Good luck H
	Appreciate 1 Quote

08-16-2013, 10:06 PM	#4
HFW003 Colonel 1905 Rep 2,673 Posts Drives: MY19 LBB M2 Comp Join Date: Apr 2013 Location: Newcastle, Australia iTrader: (0)	You're welcome!
	Appreciate 0 Quote

08-17-2013, 12:52 PM	#5
mocohead Lieutenant 38 Rep 465 Posts Drives: '16 M235i 6MT & 12 128i Msport Join Date: Sep 2010 Location: CA iTrader: (1)	Let's chat about this a bit further as I was wondering the same thing. Recently I had a bad experience after changing my spark plugs. The car was in limp mode, CEL on, and it would not start at all. There were TONS of codes stored when the car got to the dealer. But I ran Tool32, all of the steps described above, and it did not find ANY codes. Thoughts?
	Appreciate 0 Quote

12-19-2013, 09:51 AM	#10
navy.doc New Member 5 Rep 17 Posts Drives: 2014 335i M-Sport Join Date: Feb 2010 Location: Puerto Rico iTrader: (0)	I'm trying to use Tool32, but I think I have the English version, not the german how i can get the german version. Thanks __________________ ED 2014 335i M-Sport AW - Sport Automatic, 403M, M Sport Brakes, NBT, Hupper Optik - 40% Tint, M Performance Black Kidney Grille, Rear Spoiler and Front Lip Coming Soon: Borla Cat-Back S-Type
	Appreciate 0 Quote

12-19-2013, 02:43 PM	#11
HFW003 Colonel 1905 Rep 2,673 Posts Drives: MY19 LBB M2 Comp Join Date: Apr 2013 Location: Newcastle, Australia iTrader: (0)	If you, like many other, have received the coding package from Shawn then it is in there. You just need to search for it.
	Appreciate 0 Quote

01-14-2014, 03:17 AM	#13
vitchie Private 21 Rep 68 Posts Drives: 2013 F30 328i Join Date: Jan 2013 Location: South Africa iTrader: (0) Garage List 2013 BMW 328i (F30) [0.00]	Hi guys, I got the coding pack, but not sure where the german version of tool 32 is? There is only 1 tool32 in bin?
	Appreciate 0 Quote

01-14-2014, 04:07 AM	#14
HFW003 Colonel 1905 Rep 2,673 Posts Drives: MY19 LBB M2 Comp Join Date: Apr 2013 Location: Newcastle, Australia iTrader: (0)	I'm not sure what Shawn now sends out mate. Just try the one and see if it works. If it's not the correct one you will notice it just hangs when you try to use it.
	Appreciate 0 Quote

01-14-2014, 04:17 AM	#15
vitchie Private 21 Rep 68 Posts Drives: 2013 F30 328i Join Date: Jan 2013 Location: South Africa iTrader: (0) Garage List 2013 BMW 328i (F30) [0.00]	Ok, figured it out. Had to run it as administrator.
	Appreciate 0 Quote

01-14-2014, 10:42 PM	#16
joeaye New Member 0 Rep 16 Posts Drives: '17 440i xDrive Vert w/ Mspt Join Date: Mar 2012 Location: Queens/LI iTrader: (0)	I had the same issue with Tool32, I needed to run it on windows pro because it was 32bit and my machine only ran 64bit (or windows xp/vista). I tested this on a few computers too and that was the common denominator.
	Appreciate 0 Quote

01-15-2014, 01:59 AM	#17
steddyman Lieutenant 33 Rep 458 Posts Drives: BMW F30 330D M-Sport Auto Join Date: Nov 2013 Location: UK iTrader: (0)	I found when VO coding the KOMBI it reset the date and time. This causes the warning triangle to appear and setting it correct on the iDrive clears it.
	Appreciate 1 Quote

06-02-2014, 04:55 PM	#22
F30_NY91 New Member 0 Rep 6 Posts Drives: 2014 335i M-Sport Join Date: Oct 2013 Location: Long Island, NY iTrader: (0)	Hi Shawn I have an engine code also. Do you have the latest tool32? __________________ 2014 F30 335i ///M-Sport, 2006 E60 530i (Sold), 2001 E46 330i, 2005 Volvo S60 (Sold)
	Appreciate 0 Quote

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search