[jkwhar]

Originally Posted by Suprnowa

I connected and coded as you wrote. I took the power of the camera from the reverse lamp
Unfortunately, the image from the camera is black and white, then some horizontal lines appear and then the image turns off everything is gray.
Previously, the same camera connected to Android worked Ok and the image was in color

Look into something like this...read the description on the listing. It may or may not fix your issue.
https://www.amazon.com/Dasaita-Capac.../dp/B074P35T3M

[hugo325]

Hi everyone,

I also have the same problem regarding the display of the "TRSVC" module in my SVT.
My FEM module does not have any default wire on the K_CAN 51/52 pins (A173*8B).
Once connected, I checked the voltage levels on the connector of my "TRSVC" module (A167*2B). All is OK

I have 12V on pin 7 (Supply, terminal 15)
1.8V on pin 6 (K-CAN_L)
3.3V on pin 5 (K_CAN_H)
Pin 1 is well connected to the ground plane.

I add "3AG" in my FA code.
Unfortunately I don't have a "TRSVC" module that appears in my SVT ...
I have the fault error :
E59449 No message (status, qualifier rear-view, 0x39B), REM receiver, TRSVC transmitter

My car model is : 118i (F20) LCI (04/2018), I-step 17-11-540.

The reference of my FEM is : 61358707677-01
ZB FEM LEAR V13
HW: D9.0, SW: 16.114.030

It's so strange because when I do a TAL calculating (with my Istep shipment), I get a TRSVC.
So normally my TRSVC module should be recognized ...
Only the hardware version is wrong between the TRSVC display by TAL calculating (HW: 10.003.000) and my TRVSC purchase (HW: 10.002.000).



Does anyone have an explanation to this ?

[atzebmw]

Originally Posted by hugo325

Hi everyone,

I also have the same problem regarding the display of the "TRSVC" module in my SVT.
My FEM module does not have any default wire on the K_CAN 51/52 pins (A173*8B).
Once connected, I checked the voltage levels on the connector of my "TRSVC" module (A167*2B). All is OK

I have 12V on pin 7 (Supply, terminal 15)
1.8V on pin 6 (K-CAN_L)
3.3V on pin 5 (K_CAN_H)
Pin 1 is well connected to the ground plane.

I add "3AG" in my FA code.
Unfortunately I don't have a "TRSVC" module that appears in my SVT ...
I have the fault error :
E59449 No message (status, qualifier rear-view, 0x39B), REM receiver, TRSVC transmitter

You can try to connect the 2 K_CAN wires with Pin 33/34 on A173*7B.

https://www.newtis.info/tisv2/a/en/f...-2v/1VnXT4PbeT

If you then have the same problem the TRSVC is defective i think.

[hugo325]

I just checked, I don't have anything on pin 33/34 (A173*7B).

I try to connect the bus to these 2 pins anyway ?

The exacte wiring schematic is :
https://www.newtis.info/tisv2/a/en/f...-2v/1VnXgq8kBl

[atzebmw]

Originally Posted by hugo325

I just checked, I don't have anything on pin 33/34 (A173*7B).

I try to connect the bus to these 2 pins anyway ?

The exacte wiring schematic is :
https://www.newtis.info/tisv2/a/en/f...-2v/1VnXgq8kBl

But on pin 33/34 (A173 * 7B) the control unit for the air conditioning must have be connected. So the K_CAN must definitely be activated there. And that in any case.
You can anyway try connecting the 2 pins there.

[hugo325]

No sorry on my car 118i, the air conditionning is connecting to K_CAN2 on the connector X20*1B.

I think my TRSVC module is dead, so I will change it in few day...
I hope I am right.

[Maxfusion]

Originally Posted by Jaykob

Hi guys!
I'm trying to figure out the best solution for my 6/2016 320d F31 with NBT EVO ID4.
I'm reading that mine doesn't support ICAM, is that correct?
However I've heard that there are special adapters (CAN-filters) that I could use? Like this one: http://carsystems.com.ua/bmw-product...fit-adapter-en

Quality-wise the ICAM should be preferred over the TRSVC solution, right?

I have the same question. 320I 06/2016 with retrofitted NBT Evo Touch ID6.
Can we install ICAM natively without special adapters and without changing FEM to a newer version?

[scoopy]

I dont have can wires in pin51 and 52 then i saw these i tried using positap however i dont have any trsvc module showing up in esys and ista can someone help me?[IMG][/IMG]

Alsontried the yellow red anf yellow orange but not working

Adding the error in ista

[scoopy]

quick question if you VO 3AG does that mean trsvc should be in ista? regardless if the ground and 12v is not connected or the can wires is wrong should it be in insta and should shaded red? or if there's not power or wrong can wires it will not show up in ista?

[scoopy]

Soldered and added a line for pin 51 and 52. Started the car and check the voltage in the pin of the trsvc. Pin 1 and 7 i get 14.2v. Orange/green wire i get 3.5v. Green wire i get 1v. Does that mean wirings are all correct anfd the problem is my module might be broken?

[atzebmw]

Originally Posted by scoopy

Soldered and added a line for pin 51 and 52. Started the car and check the voltage in the pin of the trsvc. Pin 1 and 7 i get 14.2v. Orange/green wire i get 3.5v. Green wire i get 1v. Does that mean wirings are all correct anfd the problem is my module might be broken?

If the connection isn't correct it will not show in ISTA or E-Sys.

You can only measure the ground or 12V but not the KCAN lines.
After you connected to Pin 51 and 52 do you see the TRSVC now in ISTA or E-Sys?

[scoopy]

Originally Posted by atzebmw

If the connection isn't correct it will not show in ISTA or E-Sys.

You can only measure the ground or 12V but not the KCAN lines.
After you connected to Pin 51 and 52 do you see the TRSVC now in ISTA or E-Sys?

yes i did. was able to connect it already and was able to install an 8.8" screen also. what i want to do next is to retrofit the pdc/camera button

[SniPro]

Hi all,
Does anybody know if EntryNav2 head unit supports in general original rear view camera iCam (66 53 7 951 083) retrofit?
In case only some of EntryNav2 supports does HU with part number 65 12 8 720 702 supports it? I can not find any evidence that FBAS on it working and it supports option 3AG.
Thanks in advance

[DimitrisM3]

so i have e90 with nbt unit how possible is to install oem camera retrofit from f30?? i think can be done i am not very sure..
need small help guys !!

[alecs_1000rr]

Hi guys and thx a lot for all the incredible info that i found here. I ve installed the camera like roxxor said and for the nbt evo, the navi pins are red21, shield 23 and white 24. I had the short cable, the one for the f10 so i ve mounted the module, in the place that other cars have the combox. I had to split the cables, so that i can keep the green in the back, to connect it to the fuse box beside the combox and the kcan to route them neer the idrive.
All in all, it works perfect. Thx a lot again, all of you are great!

[Queiroz]

Hello guys,
If someone can help me out.
I’ve installed a rvc in my 2013 f31
Coded fdl but can’t get picture in NBT
I have the menu option to select rvc but no image...
Just a black square where the video feed should be.
I’ve tryed different settings, icam, trsvc, and nothing seems to work.
It’s an emulator box, connected to pin 21, 23 and 24.
It’s also connected in quad lock to power, ground, can-H and can-L
Any thoughts?
Thanks

[Queiroz]

[img]https://i.ibb.co/wN4vKS4/780220-CA-0...4-C3-A0862.jpg[/img]

This is what I get

[Queiroz]

[img]https://i.ibb.co/YLSQ6JF/B76296-F2-4...370-BCF284.jpg[/img]

Any opinions please?

[THE_AVIATOR]

Originally Posted by Queiroz

[img]https://i.ibb.co/YLSQ6JF/B76296-F2-4...370-BCF284.jpg[/img]

Any opinions please?

Do you receive any failure messages? i.e Camera fault, or something? Tell me your setup with the emulator, where is the camera connected? The emulator is replacing the control unit?

[Queiroz]

Originally Posted by THE_AVIATOR

Do you receive any failure messages? i.e Camera fault, or something? Tell me your setup with the emulator, where is the camera connected? The emulator is replacing the control unit?

Hello,
I only have this error in ista.
Camera is connected to emulator box, seller is great, send a new box to see if that's the problem, I'm going to check tonight

[Queiroz]

[img]https://i.ibb.co/5RkQJ4N/4-D907196-A...57-E37-ED1.jpg[/img]
[img]https://i.ibb.co/Wpj5GyF/E9-C04-A56-...-CF7149-A9.jpg[/img]


Can someone share any opinions please?
Thanks

[DLucian]

Looking into doing this retrofit and I have a question (sorry if it has been asked, did try and search through posts first).

I am looking into different TRSVC modules from scrappers. They are usually quite old (like 2010 - 2013). I see the part number has updated over time.

My main concern is having the moving guide lines available and the obstacle highlights. Do I need a TRSVC module upwards of a certain year (or part number) to have this available?

What I am missing is where are these features implemented. In the HU / PDC or in the TRSVC module? If they are not coming from the TRSVC then my guess will be that the age of the module doesn't matter. Am I correct?

Thanks in advance.