04-19-2024, 08:06 PM | #14675 |
Captain
372
Rep 895
Posts
Drives: F32 428i Xdrive
Join Date: Aug 2020
Location: Texas
|
Did an oil change, Ceratec, jectron and transfer case today!
Obligatory before and after fluid Pics below
__________________
|
Appreciate
0
|
04-20-2024, 06:39 PM | #14676 |
First Lieutenant
360
Rep 326
Posts |
added these bad boys back on for the summer.
|
Appreciate
5
|
04-21-2024, 04:09 AM | #14677 |
Private
59
Rep 81
Posts |
Went for a drive with the club!
|
Appreciate
6
|
04-21-2024, 08:00 AM | #14678 |
First Lieutenant
404
Rep 358
Posts |
Yesterday I took a break from the never ending spring yard work (thank you rain!) to install some long overdue upgrades that were hanging around in my garage. First up are euro spec auxiliry radiator frames with integrated stone guards. Why USA models didn't get these makes no sense! Pretty easy install with no radiator removal required, but note you'll need a long T25 Torx bit to remove the old frames. Second was replacing the brake disc set screws with stainless steel versions. Last, but not least was a mild engine bay aesthetic bolt/washer upgrade for an OEM+ look.... Next weekend I'll be mounting rear carbon fiber arch guards to match the front guards. Cheers!
|
Appreciate
5
|
04-21-2024, 09:42 AM | #14679 |
Second Lieutenant
109
Rep 293
Posts
Drives: 2016 340i X Drive
Join Date: Dec 2015
Location: Pa.
|
Nice job on the radiator frame! Where did you get if from, and can you give some installation guidance?
|
Appreciate
0
|
04-21-2024, 10:04 AM | #14680 |
Lieutenant
202
Rep 584
Posts |
KLE Failure. Replacement installed
Well I got the red circle of death on the charging socket of my 330e. The car would charge the batteries on its own power, but not using a plug. The KLE unit is basically a DC to AC converter. BMW wanted €1,500 for the part. And if it was replaced by BMW. That would be an additional €1,200- €1,300 for labor. So €2,800ish for the complete job.
I decide to do the swap myself. So I sourced a new unit from Germany coming with 1 year warranty for €700 delivered. I needed a small bottle of coolant. and that was it. I didn't have access to a car hoist, So I carried out the work with a car jack and a couple of axle stands in place. The complete job took me 3 hours. I could have easily did it in less then 2 hours if I had the car in the air. Once installed and complete. I plugged in to the charger and the led on the socket went blue after a couple of seconds. The job was a success At a quarter of the price of what BMW wanted to charge I'm happy out.
__________________
[/B]2017 330e M Performance, MG Flasher Stage 2, RM Motors DP, xHP Stage 3, Armaspeed CIA
|
Appreciate
4
|
04-21-2024, 10:15 AM | #14681 | |
///M
165
Rep 631
Posts
Drives: '18 F80 M3 ZCP, '14 F30 328i
Join Date: May 2017
Location: Raleigh, NC ITB
|
Quote:
|
|
Appreciate
0
|
04-21-2024, 11:35 AM | #14682 | |
Second Lieutenant
127
Rep 276
Posts |
Quote:
|
|
Appreciate
0
|
04-21-2024, 12:30 PM | #14683 | |
First Lieutenant
404
Rep 358
Posts |
Quote:
Replacement is straightforward: Set car on jack stands Remove front wheels Remove front fender liners (10 8mm screws each) Unclip radiator from top frame clips, tilt out the top of radiator and lift up to remove it from the frame Gently set radiator away from the frame Remove the three T25 screws securing the frame its mounting points. You'll need a long T25 for this Gently remove the frame Installation of the new frame is in reverse order. Note for me, getting the new frame set in place was the biggest PIA as the frame sits over the cooling duct and it takes some manipulating of the top of the rubbish duct to align. On the passenger side I had to remove the horn to gain access to the duct. Good luck! |
|
Appreciate
1
_ObiJon197.00 |
04-21-2024, 04:05 PM | #14684 |
Second Lieutenant
197
Rep 296
Posts |
Spent yesterday and today washing, clay baring and ceramic coating the car and wheels. Did it wheels off, so I can ceramic coat the brake calipers too. My back hurts.
|
Appreciate
1
oem.plus_440gc353.00 |
04-21-2024, 04:12 PM | #14685 |
Private
21
Rep 53
Posts |
Bagged my F32, threw on Meisters
326Power stud conversion + Work Meisters + Pirelli Pzero tires + Airlift + P2M checkered floor mats. I'm so happy with how it turned out.
Instagram @saigonair! |
Appreciate
0
|
04-21-2024, 06:07 PM | #14686 |
Private
213
Rep 76
Posts |
Fitment test of my new dedicated track wheels
|
Appreciate
2
oem.plus_440gc353.00 motofiend10.50 |
04-21-2024, 08:13 PM | #14687 |
Lieutenant Colonel
1127
Rep 1,508
Posts |
|
Appreciate
0
|
Yesterday, 09:49 AM | #14688 |
Mr OEM
655
Rep 78
Posts
Drives: 2012 BMW 335i
Join Date: May 2023
Location: Mbombela
|
Did a thorough clean of the engine bay!
Looks very good for 385,000km (240,000mls) Just need a new coolant overflow line now! See attached: |
Appreciate
0
|
Yesterday, 09:52 AM | #14689 |
Lieutenant
202
Rep 584
Posts |
|
Appreciate
0
|
Yesterday, 10:52 AM | #14691 |
Lieutenant
230
Rep 480
Posts |
Looking good! I’ve been meaning to do this for a while but honestly just afraid I will get water somewhere that it’s not supposed to go. Any pointers?
|
Appreciate
0
|
Yesterday, 10:56 AM | #14692 | |
Mr OEM
655
Rep 78
Posts
Drives: 2012 BMW 335i
Join Date: May 2023
Location: Mbombela
|
Quote:
I wouldn't spray water into an engine bay personally, however I have heard that steam cleaners are also a good way to clean your engine bay. |
|
Appreciate
0
|
Yesterday, 04:16 PM | #14693 |
Brigadier General
10918
Rep 4,550
Posts
Drives: 2015 328d xDrive
Join Date: Aug 2010
Location: NoVA
|
Got a new dashcam (BlackVue 970x Plus)
If anyone's interested in buying my old one for cheap, I'm selling it here
__________________
Last edited by AndrewC1989; Yesterday at 04:26 PM.. |
Appreciate
1
toxik2433.50 |
Yesterday, 04:30 PM | #14694 |
Lieutenant Colonel
2434
Rep 1,811
Posts |
hope it has good shopping cart capture
__________________
|
Appreciate
1
AndrewC198910917.50 |
Post Reply |
Bookmarks |
|
|