F30POST
F30POST
2012-2015 BMW 3-Series and 4-Series Forum
BMW Garage BMW Meets Register Search Today's Posts Mark Forums Read
BMW 3-Series and 4-Series Forum (F30 / F32) | F30POST > Technical Forums > Navigation, iDrive, Audio, Video, Bluetooth, Phone, Cameras, Electronics > PDC graphical issues after NBT EVO ID6 retrofit?
Studio RSR
Post Reply
 
Thread Tools Search this Thread
      03-15-2019, 08:11 PM   #1
AcExSpades
Lieutenant
AcExSpades's Avatar
Peru
74
Rep
565
Posts

Drives: 11 MW E92 M3
Join Date: Dec 2010
Location: CNJ

iTrader: (7)

Garage List
2011 BMW M3  [0.00]
2006 Subaru WRX STi  [0.00]
Hi all,

I finally retrofitted and got my NBT EVO unit coded to my VIN. Install went fine and the system is awesome. The only disappointing thing so far is that when using the reverse camera or top down view, the car marks 4 corners around the car as if it there is something there when there isn't. Is it normal?

The functionality itself works fine and it does not beep until I actually get close to something. I have attached a picture of what I see. PS. During that picture I do have a car on the left top corner and a piece of a car on the bottom left corner, hence why the sensors is catching a bigger area.

Thanks
Attached Images
 
Appreciate 0
      07-04-2019, 02:31 AM   #2
gecko.ch
Enlisted Member
gecko.ch's Avatar
Switzerland
17
Rep
41
Posts

Drives: G01 M40
Join Date: Jul 2019
Location: Winterthur, Switzerland

iTrader: (0)

Hi

I have the same Problem with my retrofitted NBTevo ID6 unit.
You have solved this Problem?

thanks
Appreciate 0
      07-04-2019, 04:23 AM   #3
larrylam646
Lieutenant
larrylam646's Avatar
Canada
371
Rep
461
Posts

Drives: 2020 M340i xDrive
Join Date: Jul 2015
Location: Ottawa

iTrader: (2)

CAFD PDC Sensor settings

Confirm your EVO CAFD file settings for the number of front and rear PDC sensors are set to four sensors:

3001 EXBOX --> PDC_SENSOR_VORN --> 4_sensoren (Werte=01)
3001 EXBOX --> PDC_SENSOR_HINTEN --> 4_sensoren (Werte=01)

Larry
__________________
2020 Black Sapphire M340iX
2014 Estoril Blue 435iX - sold
Appreciate 0
      07-04-2019, 06:09 AM   #4
gecko.ch
Enlisted Member
gecko.ch's Avatar
Switzerland
17
Rep
41
Posts

Drives: G01 M40
Join Date: Jul 2019
Location: Winterthur, Switzerland

iTrader: (0)

i have not a f30, i have a f20 with 6 sensors each, and the values are with 6 sensors.
i tried with 4, but the same.
Appreciate 0
      07-07-2019, 01:27 PM   #5
gecko.ch
Enlisted Member
gecko.ch's Avatar
Switzerland
17
Rep
41
Posts

Drives: G01 M40
Join Date: Jul 2019
Location: Winterthur, Switzerland

iTrader: (0)

So i have new information.
I have the park assist. The 4 sensors in front/back are for the pdc and the additional 2 sensors are for the park assist „flankenschutz“

My current config are:
3001 exbox > communication_parkmaster > gen2 0x02
3001 exbox > macro_pma_einparken > gen2_ohne_konf 0x03
3001 exbox > auto_pdc > aktiv 0x01
3001 exbox > pdc_flankenschutz > aktiv 0x01
3001 exbox > pdc_generation > gen2 0x01
3001 exbox > pdc_sensor_hinten > 4_sensoren 0x01
3001 exbox > pdc_sensor_vorn > 4_sensoren 0x01

So looks my pdc, the beep works, but no sensor lines only the 4 corners...
Attached Images
 
Appreciate 0
      07-07-2019, 02:38 PM   #6
larrylam646
Lieutenant
larrylam646's Avatar
Canada
371
Rep
461
Posts

Drives: 2020 M340i xDrive
Join Date: Jul 2015
Location: Ottawa

iTrader: (2)

Quote:
Originally Posted by gecko.ch View Post
So i have new information.
I have the park assist. The 4 sensors in front/back are for the pdc and the additional 2 sensors are for the park assist „flankenschutz“

My current config are:
3001 exbox > communication_parkmaster > gen2 0x02
3001 exbox > macro_pma_einparken > gen2_ohne_konf 0x03
3001 exbox > auto_pdc > aktiv 0x01
3001 exbox > pdc_flankenschutz > aktiv 0x01
3001 exbox > pdc_generation > gen2 0x01
3001 exbox > pdc_sensor_hinten > 4_sensoren 0x01
3001 exbox > pdc_sensor_vorn > 4_sensoren 0x01

So looks my pdc, the beep works, but no sensor lines only the 4 corners...
For my vehicle, all of the listed parameters are the same except for:

3001 exbox > pdc_generation > gen1 0x00
__________________
2020 Black Sapphire M340iX
2014 Estoril Blue 435iX - sold
Appreciate 0
      07-08-2019, 01:56 AM   #7
gecko.ch
Enlisted Member
gecko.ch's Avatar
Switzerland
17
Rep
41
Posts

Drives: G01 M40
Join Date: Jul 2019
Location: Winterthur, Switzerland

iTrader: (0)

ok, i have tryed with gen1, then looks like so, the 4 corners still there.
Attached Images
 
Appreciate 0
      07-08-2019, 03:32 AM   #8
steve@codemybimmer
BimmerPost Supporting Vendor
steve@codemybimmer's Avatar
Hong Kong
663
Rep
1,975
Posts


Drives: 2020 G20 320i M Sport
Join Date: Apr 2010
Location: Canada & HK

iTrader: (2)

Garage List
Do you have option 5DP for Parking Assist? This issue only seems to affect vehicles with that specific option since it has the all around PDC.
__________________
CMB Solutions Limited |codemybimmer.ca
Vehicle Diagnostics | CarPlay Solutions | Retrofit & Repair Consulting/Programming
steve.ma@cmbsolutionsltd.com | www.codemybimmer.ca
Online Store | Remote Coding Package| ID6 Retrofit for almost all F Chassis BMWs
Appreciate 0
      07-08-2019, 04:04 AM   #9
gecko.ch
Enlisted Member
gecko.ch's Avatar
Switzerland
17
Rep
41
Posts

Drives: G01 M40
Join Date: Jul 2019
Location: Winterthur, Switzerland

iTrader: (0)

yes, i have 5DP factory fitted
Appreciate 0
      07-08-2019, 05:06 AM   #10
larrylam646
Lieutenant
larrylam646's Avatar
Canada
371
Rep
461
Posts

Drives: 2020 M340i xDrive
Join Date: Jul 2015
Location: Ottawa

iTrader: (2)

Quote:
Originally Posted by larrylam646 View Post
For my vehicle, all of the listed parameters are the same except for:

3001 exbox > pdc_generation > gen1 0x00
Values of other parameters with "pdc" and "pma" in my CAFD file (CAFD_00001EF6_006_040_006.ncd):

3001 EXBOX MACRO_PDC aktiv 0x01
3001 EXBOX PDC_ABSTAENDE_VERSION alt 0x00
3001 EXBOX PDC_DIRECTION vertikal 0x00
3001 EXBOX PDC_3D nicht_aktiv 0x00
3001 EXBOX ACTIVE_PDC_FLANKENBREMSUNG nicht_aktiv 0x00
3001 EXBOX ACTIVE_PDC_DEFAULT_ON nicht_aktiv 0x00
3001 EXBOX ACTIVE_PDC nicht_aktiv 0x00
3001 EXBOX PDC_DARSTELLUNG_V2 aktiv 0x01

3005 DISPLAY_PIP_CONFIG ZIN_SEMI_PERMANENT_DISPLAYS_PDC_PMA nicht_activ 0x00

3000 HMI CURSORPOSITION_PMA_AUSRICHTUNG laengs 0x00
3000 HMI PMALQ_BEDIENUNG mit_Dauerdruck 0x01

3001 EXBOX MACRO_PMA_AUSPARKEN nicht_aktiv 0x00
__________________
2020 Black Sapphire M340iX
2014 Estoril Blue 435iX - sold
Appreciate 0
      07-08-2019, 06:39 AM   #11
gecko.ch
Enlisted Member
gecko.ch's Avatar
Switzerland
17
Rep
41
Posts

Drives: G01 M40
Join Date: Jul 2019
Location: Winterthur, Switzerland

iTrader: (0)

thank you.

this 2 values i dont' have
3001 EXBOX ACTIVE_PDC_FLANKENBREMSUNG nicht_aktiv 0x00
3001 EXBOX ACTIVE_PDC_DEFAULT_ON nicht_aktiv 0x00

but i try with
3001 exbox > pdc_flankenschutz > nicht_aktiv 0x00
and now i think it looks good, but i dont know how the park assist works without Flankenschutz.

do you have the value "pdc_flankenschutz"?
Appreciate 0
      07-08-2019, 04:20 PM   #12
larrylam646
Lieutenant
larrylam646's Avatar
Canada
371
Rep
461
Posts

Drives: 2020 M340i xDrive
Join Date: Jul 2015
Location: Ottawa

iTrader: (2)

Quote:
Originally Posted by gecko.ch View Post
thank you.

this 2 values i dont' have
3001 EXBOX ACTIVE_PDC_FLANKENBREMSUNG nicht_aktiv 0x00
3001 EXBOX ACTIVE_PDC_DEFAULT_ON nicht_aktiv 0x00

but i try with
3001 exbox > pdc_flankenschutz > nicht_aktiv 0x00
and now i think it looks good, but i dont know how the park assist works without Flankenschutz.

do you have the value "pdc_flankenschutz"?
The two values you do not have may be due to different ilevel versions.

Regarding "pdc_flankenschutz", yes I do have this parameter set to aktiv 0x01.

Since I have responded incrementally on my setting over 2 posts, I will summarize my PDC/PMA related settings below:

3001 exbox > communication_parkmaster > gen2 0x02
3001 exbox > macro_pma_einparken > gen2_ohne_konf 0x03
3001 exbox > auto_pdc > aktiv 0x01
3001 exbox > pdc_flankenschutz > aktiv 0x01
3001 exbox > pdc_generation > gen1 0x00
3001 exbox > pdc_sensor_hinten > 4_sensoren 0x01
3001 exbox > pdc_sensor_vorn > 4_sensoren 0x01

3001 EXBOX MACRO_PDC aktiv 0x01
3001 EXBOX PDC_ABSTAENDE_VERSION alt 0x00
3001 EXBOX PDC_DIRECTION vertikal 0x00
3001 EXBOX PDC_3D nicht_aktiv 0x00
3001 EXBOX ACTIVE_PDC_FLANKENBREMSUNG nicht_aktiv 0x00
3001 EXBOX ACTIVE_PDC_DEFAULT_ON nicht_aktiv 0x00
3001 EXBOX ACTIVE_PDC nicht_aktiv 0x00
3001 EXBOX PDC_DARSTELLUNG_V2 aktiv 0x01

3005 DISPLAY_PIP_CONFIG ZIN_SEMI_PERMANENT_DISPLAYS_PDC_PMA nicht_activ 0x00

3000 HMI CURSORPOSITION_PMA_AUSRICHTUNG laengs 0x00
3000 HMI PMALQ_BEDIENUNG mit_Dauerdruck 0x01

3001 EXBOX MACRO_PMA_AUSPARKEN nicht_aktiv 0x00


If you wish to compare CAFD files, please PM a email address and I will send to you my CAFD file.

Larry
__________________
2020 Black Sapphire M340iX
2014 Estoril Blue 435iX - sold
Appreciate 0
      07-10-2019, 03:32 PM   #13
AcExSpades
Lieutenant
AcExSpades's Avatar
Peru
74
Rep
565
Posts

Drives: 11 MW E92 M3
Join Date: Dec 2010
Location: CNJ

iTrader: (7)

Garage List
2011 BMW M3  [0.00]
2006 Subaru WRX STi  [0.00]
Hi everyone, I'm not sure why I didn't get notified, but I actually gave up and now it looks like there may be a fix?

@gecko.ch - I know you mentioned that you don't know whether park assist work now. Does it? Can you attach a picture on how the graphics look on the idrive?
Appreciate 0
      07-11-2019, 03:53 AM   #14
gecko.ch
Enlisted Member
gecko.ch's Avatar
Switzerland
17
Rep
41
Posts

Drives: G01 M40
Join Date: Jul 2019
Location: Winterthur, Switzerland

iTrader: (0)

hi at all

i have compared all settings from Larry, but no luck. it looks like my Pictures above.
i played with the gatewytable setting, standard is table_1, i tried every table but no luck. with table 3-5 the graphic looks better, but the park assist don't work.
Appreciate 0
      07-12-2019, 11:30 AM   #15
Sanelko
Second Lieutenant
Sanelko's Avatar
70
Rep
235
Posts

Drives: 2012 Jet Black 328i
Join Date: Jan 2016
Location: Seattle

iTrader: (0)

I'm speaking on the F30 here as I do not know if it is the same case for the F20, but anyways the PMA module hardware changed between the Pre-LCI and LCI, as well as the PDC setup. In order for to VO coding to work as-is with the newer build date for the EVO, you need to get the newer part # PMA module as well as add two additional PDC type sensors to the rear (total of 6 front and 6 rear). Otherwise, you need to code the following on the EVO in order for it to work with the older PMA module:

MACRO_PMA_EINPARKEN > gen1_ohne_konf
PDC_FLANKENSCHUTZ > nicht_aktiv
AUTO_PDC > nicht_aktiv
COMMUNICATION_PARKMASTER > gen1
Appreciate 0
      07-13-2019, 10:40 AM   #16
gecko.ch
Enlisted Member
gecko.ch's Avatar
Switzerland
17
Rep
41
Posts

Drives: G01 M40
Join Date: Jul 2019
Location: Winterthur, Switzerland

iTrader: (0)

I have a F20 LCI BY 7/2015 with factory fitted park assist. 6 sensors in front/rear. I have replaced my evo id4 unit with a new id6 unit and now i have this pdc issue.
Appreciate 0
      07-14-2019, 12:34 PM   #17
larrylam646
Lieutenant
larrylam646's Avatar
Canada
371
Rep
461
Posts

Drives: 2020 M340i xDrive
Join Date: Jul 2015
Location: Ottawa

iTrader: (2)

Quote:
Originally Posted by gecko.ch View Post
I have a F20 LCI BY 7/2015 with factory fitted park assist. 6 sensors in front/rear. I have replaced my evo id4 unit with a new id6 unit and now i have this pdc issue.
Did you VO Code your PMA2 with at least a newer manufacturing date (Zeitkriterium) and possibly a newer type code (Typschlussel)?

But first, try FDL editing/coding PMA2 with the following change:

3030 PdcHMI --> IDX_DARSTELLUNGS_VARIANTE --> ID5 (0x05)

Larry
__________________
2020 Black Sapphire M340iX
2014 Estoril Blue 435iX - sold
Appreciate 1
      07-30-2019, 06:01 AM   #18
gecko.ch
Enlisted Member
gecko.ch's Avatar
Switzerland
17
Rep
41
Posts

Drives: G01 M40
Join Date: Jul 2019
Location: Winterthur, Switzerland

iTrader: (0)

Quote:
Originally Posted by larrylam646 View Post
Did you VO Code your PMA2 with at least a newer manufacturing date (Zeitkriterium) and possibly a newer type code (Typschlussel)?

But first, try FDL editing/coding PMA2 with the following change:

3030 PdcHMI --> IDX_DARSTELLUNGS_VARIANTE --> ID5 (0x05)

Larry
Hi Larry

Sorry for my late Response. i had Problems with my e-sys, meanwhileit runs and coded the pma2 ecu with this 3030 PdcHMI --> IDX_DARSTELLUNGS_VARIANTE --> ID5 (0x05)

and seems looks good...but...my Picture took i in my garage and in the back/right corner is a pillar, with my id4 unit it was all red in my pdc grafik and with my id5 not?
Attached Images
 
Appreciate 0
      07-31-2019, 05:22 AM   #19
gecko.ch
Enlisted Member
gecko.ch's Avatar
Switzerland
17
Rep
41
Posts

Drives: G01 M40
Join Date: Jul 2019
Location: Winterthur, Switzerland

iTrader: (0)

so finally i got the solution for me.
i changed additionally in the pma2 this value:
3030 PdcHmi > SDW_enable > 02 = SDW_on

now it looks perfect
Attached Images
 
Appreciate 1
      07-31-2019, 07:17 PM   #20
larrylam646
Lieutenant
larrylam646's Avatar
Canada
371
Rep
461
Posts

Drives: 2020 M340i xDrive
Join Date: Jul 2015
Location: Ottawa

iTrader: (2)

Quote:
Originally Posted by gecko.ch View Post
so finally i got the solution for me.
i changed additionally in the pma2 this value:
3030 PdcHmi > SDW_enable > 02 = SDW_on

now it looks perfect
Great! I am glad you figured it out.

The pic in your previous post did not look right. Pic of my pdc/pma2...

Larry
Attached Images
 
__________________
2020 Black Sapphire M340iX
2014 Estoril Blue 435iX - sold
Appreciate 0
      10-05-2019, 07:58 PM   #21
bimleaf
Private First Class
27
Rep
102
Posts

Drives: G20
Join Date: Sep 2019
Location: GVR

iTrader: (0)

For LCI F30 (production year 2016), should 3001 exbox > pdc_sensor_hinten and 3001 exbox > pdc_sensor_vorn = 4 or 6?

I counted 6 physical sensors front and back.
Appreciate 0
      10-06-2019, 04:27 AM   #22
gecko.ch
Enlisted Member
gecko.ch's Avatar
Switzerland
17
Rep
41
Posts

Drives: G01 M40
Join Date: Jul 2019
Location: Winterthur, Switzerland

iTrader: (0)

Quote:
Originally Posted by bimleaf View Post
For LCI F30 (production year 2016), should 3001 exbox > pdc_sensor_hinten and 3001 exbox > pdc_sensor_vorn = 4 or 6?

I counted 6 physical sensors front and back.
4 sensors. The additional 2 in front and back are for the parkassist.
Appreciate 0
Post Reply

Bookmarks

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off



All times are GMT -5. The time now is 07:50 AM.




f30post
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
1Addicts.com, BIMMERPOST.com, E90Post.com, F30Post.com, M3Post.com, ZPost.com, 5Post.com, 6Post.com, 7Post.com, XBimmers.com logo and trademark are properties of BIMMERPOST