[vespinoza82]

Hello all,

I have downloaded these below to code my 16 428 GC. I am mainly looking for seatbelt chime disable and initial idrive warning disable to start with. Is this all need below or do i need an updated version?
Thanks in advance.

Psdz data 4.18.33
Esys 3.27.1

[shawnsheridan]

Originally Posted by vespinoza82

Hello all,

I have downloaded these below to code my 16 428 GC. I am mainly looking for seatbelt chime disable and initial idrive warning disable to start with. Is this all need below or do i need an updated version?
Thanks in advance.

Psdz data 4.18.33
Esys 3.27.1

Should be fine. Need Esys Launcher too for FDL Coding.

[vespinoza82]

Sounds good thank you much.

[myszano1]

Hey Shawn can i I get links for the latest versions of software?

Thanks

Slaw

[shawnsheridan]

Originally Posted by myszano1

Hey Shawn can i I get links for the latest versions of software?

Thanks

Slaw

PM sent.

[robert4u]

Hi Shawn,
i would appreciate it if you can provide me a link to the latest E-Sys, Launcher and psdzdata software.
Thank you

[shawnsheridan]

Originally Posted by robert4u

Hi Shawn,
i would appreciate it if you can provide me a link to the latest E-Sys, Launcher and psdzdata software.
Thank you

PM sent.

[paszczaq]

I used bimmercode to code my tailgate for closing from the button in footwell and close without long press on key fob and it effected my soft close mechanism. All coded functions worked but boot lit slams when closing instead of slowing down when nearly closed and sucking in.

I reverted coding with bimmer code but still slams when closing however it does slow down when opening.

Couple of questions as E-sys is new to me. Is there a way to basically reset the all HKFM to what it was before bimmercode? Do I need Launcher to do it?
Or maybe I'm looking at this issue incorrectly and need to start elsewhere?

I tried re-initialisation of boot lit with ISTA and still the same and no faults shown.

[shawnsheridan]

Originally Posted by paszczaq

I used bimmercode to code my tailgate for closing from the button in footwell and close without long press on key fob and it effected my soft close mechanism. All coded functions worked but boot lit slams when closing instead of slowing down when nearly closed and sucking in.

I reverted coding with bimmer code but still slams when closing however it does slow down when opening.

Couple of questions as E-sys is new to me. Is there a way to basically reset the all HKFM to what it was before bimmercode? Do I need Launcher to do it?
Or maybe I'm looking at this issue incorrectly and need to start elsewhere?

I tried re-initialisation of boot lit with ISTA and still the same and no faults shown.

With E-Sys, VO Code HKFM with original unmodified FA, and it will be reset to factory coding.

[paszczaq]

Originally Posted by shawnsheridan

With E-Sys, VO Code HKFM with original unmodified FA, and it will be reset to factory coding.

shawn how exactly do I do it please?

[shawnsheridan]

Originally Posted by paszczaq

shawn how exactly do I do it please?

VO Coding Guide is included in E-Sys Coding package. PM sent.

[RokasLTU]

Hello,

Could I have the links, please?


Thanks in advance!

[shawnsheridan]

Originally Posted by RokasLTU

Hello,

Could I have the links, please?

Thanks in advance!

PM sent.

[paszczaq]

Originally Posted by shawnsheridan

VO Coding Guide is included in E-Sys Coding package. PM sent.

Thanks.

I believe I've done it. Saved the FA file, calculated FP etc, wrote it in VCM Master, then went to Coding, Read SVT and Coded HKFM. All successful as far as I could see.

But the boot lid still slams when closing...

[shawnsheridan]

Originally Posted by paszczaq

Thanks.

I believe I've done it. Saved the FA file, calculated FP etc, wrote it in VCM Master, then went to Coding, Read SVT and Coded HKFM. All successful as far as I could see.

But the boot lid still slams when closing...

Then issue is not a coding issue.

[robert4u]

Originally Posted by shawnsheridan

PM sent.

Thanks a lot Shawn, I really appreciate the amount of effort you put into this.

[shawnsheridan]

Originally Posted by robert4u

Thanks a lot Shawn, I really appreciate the amount of effort you put into this.

[JDMils]

I'm using the following:

E-Sys
Version 3.33.0 (build 53640) - 2018-09-18
PSdZ Version 5.07.01-2018-09-17T14:25:05Z

Code AwayDKF01.est

PSDzData Extracted from ISTA version 4.19.21

Everything works OK except for when I edit the codes I get the error:

An error occurred while processing the EST file "C:\Data\EST\Code AwayDKF01.est". See details for more information. [C157]

Not sure what I'm doing wrong?

[shawnsheridan]

Originally Posted by JDMils

I'm using the following:

E-Sys
Version 3.33.0 (build 53640) - 2018-09-18
PSdZ Version 5.07.01-2018-09-17T14:25:05Z

Code AwayDKF01.est

PSDzData Extracted from ISTA version 4.19.21

Everything works OK except for when I edit the codes I get the error:

An error occurred while processing the EST file "C:\Data\EST\Code AwayDKF01.est". See details for more information. [C157]

Not sure what I'm doing wrong?

What is validity date of Code AwayDKF01.est?

Why aren't you using E-Sys Launcher instead, which is .EST Token Solution, CAFD Mapping,and Cheat Sheets all-in-one?

[colin.t.chiang]

Hi Shawn,

Can you please send me the links for the latest files (programs and data)? Cars are 2015 F30 320d and 2016 F30 LCI 330e.

Many thanks in advance.

Cheers,
Col.

[shawnsheridan]

Originally Posted by colin.t.chiang

Hi Shawn,

Can you please send me the links for the latest files (programs and data)? Cars are 2015 F30 320d and 2016 F30 LCI 330e.

Many thanks in advance.

Cheers,
Col.

PM sent.

[RokasLTU]

What connection Target do I need to select for F31? Same as F30?

https://cdn.bimmerpost.com/forums/at...1&d=1483291144