[JoshB25]

Where have you ordered the harness from? Car is looking amazing!!

[knightsabers]

Originally Posted by JoshB25

Where have you ordered the harness from? Car is looking amazing!!

Thanks
I ordered the LCI harness from Alex @ Alpine Motorsports, they have the LCI tail lights on discount. Should've ordered through them

[david51]

Originally Posted by knightsabers

I ordered the LCI harness from Alex @ Alpine Motorsports, they have the LCI tail lights on discount. Should've ordered through them

Thanks for the info

[knightsabers]

Originally Posted by david51

Thanks for the info

You're welcome, here's a link.

http://f80.bimmerpost.com/forums/sho....php?t=1160345

[david51]

Originally Posted by knightsabers

You're welcome, here's a link to Alpine Motorsports LCI tail lights

http://f80.bimmerpost.com/forums/sho....php?t=1160345

thank you for the link
I'll buy my rear lights LCI directly from BMW, it makes me a 10% discount it cost me 677€ ttc
I'll see connectors for Alpine motorsports

[jhv]

looks fantastic!

[Ateszka86]

HI your car is amezing.

Can you help me? How you installed the M Performance Side Splitter Blades?

and

if I take 9x19 et45 front it is ok? or take 8,5x19 et35? rear 9,5x19 et40

thank you

[knightsabers]

Originally Posted by david51

thank you for the link
I'll buy my rear lights LCI directly from BMW, it makes me a 10% discount it cost me 677€ ttc
I'll see connectors for Alpine motorsports

Nice I wish I had waited before making my purchase

Alex seems like a nice guy, my harness should be arriving tomorrow; So hopefully can install it over the weekend.

[knightsabers]

Originally Posted by jhv

looks fantastic!

Thanks

[knightsabers]

Originally Posted by Ateszka86

HI your car is amezing.

Can you help me? How you installed the M Performance Side Splitter Blades?

and

if I take 9x19 et45 front it is ok? or take 8,5x19 et35? rear 9,5x19 et40

thank you

The M Performance splitter took two people to install. The process required jacking the car up one end at a time.

1. Each splitter has 3M tape pre-attached, 1 person holds the spitter in place & applies pressure to bond the splitter to the vehicle.
2. Another member would apply rivets or screw the splitter in one side at a time.

Yes it should fit. I currently have 20 X 8.5 front & 20 x 9.5 in the rear. Don't know about the offset though

[knightsabers]

Wire harness arrived Can't wait to install it

[david51]

Originally Posted by knightsabers

Wire harness arrived Can't wait to install it

thank you so much for sharing

they are the interior parts has changed?

To connect:
son green plugs into slot A174 * 12 location 14B
son red plugs into slot A174 * 17 location 12B



Do you have references please contactors

[Labeef]

Question.

Do you need to cut any wires to run the LCI tails? And then you must code correct?

[knightsabers]

Originally Posted by Labeef

Question.

Do you need to cut any wires to run the LCI tails? And then you must code correct?

No cutting required! It does require rearranging a few pins.

Coding is necessary as the inner lights has no power.

It requires advanced coding to divert power to the lights and stop the lights from flickering or throwing errors.

[david51]

Do you have references contactors please ?

[knightsabers]

Originally Posted by david51

Do you have references contactors please ?

Hi David, I don't have reference contractors. The harness is plug & play with the green wire feeding to REM - LEFT (Pin 20) & red wire feeding to REM - RIGHT (Pin 22). Then coding to open ports for power.

If you order the harness, Alex provides an authenticated link to his video instructions.

[knightsabers]

Here's a pic of the lights installed & taken by Stuart@BMRAutowerkes who helped me install it, thanks .

[david51]

Originally Posted by knightsabers

Here's a pic of the installed lights taken by Stuart@BMRAutowerkes.

Thank you I will see it

Really beautiful with new lights

[Blindside_137]

Originally Posted by knightsabers

Here's a pic of the installed lights taken by Stuart@BMRAutowerkes who helped me install it, thanks .

Absolutely killer!

[Bricktrix]

Originally Posted by knightsabers

Here's a pic of the installed lights taken by Stuart@BMRAutowerkes who helped me install it, thanks .

That is one mean looking ride
Total respect to the work and "money" put into this. Not many would.
Have done something similar on a car MANY years ago, and understand you get to a point of thinking, its all or nothing now if I'm going any further with it. Glad to see you chose the 2nd option and thanks for sharing the pics

[knightsabers]

Originally Posted by david51

Thank you I will see it

Really beautiful with new lights

Thanks They look better in person, so much brighter

[knightsabers]

Originally Posted by Blindside_137

Absolutely killer!

Thanks