[gpdrama]

Hi Shawn

Can I have the link for the latest PSdZData please?

Thanks in advance

[shawnsheridan]

Originally Posted by RDowson

Can I have the link for the lite PSdZData please?

Originally Posted by gpdrama

Hi Shawn

Can I have the link for the latest PSdZData please?

Thanks in advance

PM's sent.

[carla90]

hey shawnsheridan,
Do you have link på psdzdata full?

[shawnsheridan]

Originally Posted by carla90

hey shawnsheridan,
Do you have link på psdzdata full?

PM sent.

[pcp1234]

hi guys. do i understand it right, lite is for coding and full one for flashing ie traction control, fuel pump etc etc ? if so co i please have link for full version

i currently have v4.11.20_PSdZData_Lite. do i delete it or just replace with new files from full?

[shawnsheridan]

Originally Posted by pcp1234

hi guys. do i understand it right, lite is for coding and full one for flashing ie traction control, fuel pump etc etc ? if so co i please have link for full version

i currently have v4.11.20_PSdZData_Lite. do i delete it or just replace with new files from full?

Delete psdzdata folder and Replace. PM sent.

[auto12volts]

Hey Sawnsheridan ,can you send me links with last psdzdata lite and full please??

[shawnsheridan]

Originally Posted by auto12volts

Hey Sawnsheridan ,can you send me links with last psdzdata lite and full please??

If you had Full, you would never have any need for Lite, and even if you wanted Lite, you can make yourself from Full.

PM sent.

[pcp1234]

hi guys. thats my setup
- esys 3.28.1 (build 46869)
- psdszdata 4.11.20 lite
- 2.7.1.135 premium lanuncher

when i go into stage where is KIS/SVT target, my i level shipment and i level target are blank.

i tried using psdzdata 4.13.11 lite and 4.13.11 full too

any clues please?

[atzebmw]

Originally Posted by pcp1234

hi guys. thats my setup
- esys 3.28.1 (build 46869)
- psdszdata 4.11.20 lite
- 2.7.1.135 premium lanuncher

when i go into stage where is KIS/SVT target, my i level shipment and i level target are blank.

i tried using psdzdata 4.13.11 lite and 4.13.11 full too

any clues please?

Use E-Sys 3.27.1 and your problem will be solved.

[shawnsheridan]

Originally Posted by pcp1234

hi guys. thats my setup
- esys 3.28.1 (build 46869)
- psdszdata 4.11.20 lite
- 2.7.1.135 premium lanuncher

when i go into stage where is KIS/SVT target, my i level shipment and i level target are blank.

i tried using psdzdata 4.13.11 lite and 4.13.11 full too

any clues please?

Asked and answered:

https://f10.5post.com/forums/showpos...&postcount=330

[pcp1234]

ok, atzebmw and shawn appreciate fixing my problem. could i ask few questions please?

1. whats the difference between single and complete flash?
2. is shipment = current ? is target = new ?
3. now following steps from shawns quide; KIS/SVT target; shipment and target on my car are the same is that right? because looking at VCM => Master Tab => I-Steps it says F010-13-11-504. do i have to select my current (F010-13-11-504) or do i leave F010-18-07-530

to confirm current setup
- esys 3.27.1 build 44813
- psdszdata 4.13.11
- 2.8.2_Build_155 launcher

[shawnsheridan]

Originally Posted by pcp1234

ok, atzebmw and shawn appreciate fixing my problem. could i ask few questions please?

1. whats the difference between single and complete flash?
2. is shipment = current ? is target = new ?
3. now following steps from shawns quide; KIS/SVT target; shipment and target on my car are the same is that right? because looking at VCM => Master Tab => I-Steps it says F010-13-11-504. do i have to select my current (F010-13-11-504) or do i leave F010-18-07-530

to confirm current setup
- esys 3.27.1 build 44813
- psdszdata 4.13.11
- 2.8.2_Build_155 launcher

Just use Full as instructed. I-Step Shipment and Current are both F010-13-11-504 as car has not been programmed since leaving the factory. You need to select F010-13-11-504 as I-Step Shipment. Target is F010-18-07-530 and is not electable as it is fixed base don PSdZData version.

[pcp1234]

hi shawn, thats what I mean by saying that my shipment and target is the same. thats after stage 7

https://ibb.co/bUubkU

[shawnsheridan]

Originally Posted by pcp1234

hi shawn, thats what I mean by saying that my shipment and target is the same. thats after stage 7

https://ibb.co/bUubkU

The I-Step Shipment Drop-Down should allow changing.

You should not be using E-Sys Launcher for Flashing. It is needed only for FDL Coding. You should launch E-Sys directly, without Launcher.

And why are you connected via Gateway URL, rather than VIN? Are you using an ICOM Interface?

[pcp1234]

its in your step by step quide pal; step 3, Connect via “Connection via Gateway URL".

is vin connection better than gateway?

shall i update modules one by one or all of them? if one by one is there an order i must follow ?

[shawnsheridan]

Originally Posted by pcp1234

its in your step by step quide pal; step 3, Connect via “Connection via Gateway URL".

is vin connection better than gateway?

shall i update modules one by one or all of them? if one by one is there an order i must follow ?

It's not my Guide. I did not author it. It is however based upon on my original instruction, which the the author references in the very Step 3 you mention above. In it, I make no mention of Connection Type:

https://www.bimmerfest.com/forums/sh...0&postcount=29

The author though used Connection via Gateway URL as for him it was only way his Gateway Module (ZGW) would flash.

In any event, as I last wrote, you need to and should be able to change the I-Step shipment. If you cannot, I suggest you bypass E-Sys Launcher and use Connection via VIN, and see if I-Step Shipment opens up. If not, then we need to determine what else can be causing the issue.

[pcp1234]

sorry I was under impression that you wrote it
ok, i followed it and obviously selected connection via vin

in order not to repeat update version from-to; was F010-13-11-504 to F010-18-07-530

1. had 18modules to update so I started with ZGW, PDC and JBBF, that took approx 6mins
2. then i updated DSC2, EPS and ICM, that took 7mins
3. FRM module took shy of 5mins
4. FZD module took just over 2mins
5. SZL and EMF just shy of 2mins
6. TBX and ZBE3 in just over 3mins
7. TCB just under 13mins
8. IHKA, two attemps as first one failed, 2x 7mins
9. KOMBI, 6mins
10. CAS - 5.5 mins
11. AMP-tophb - 5mins

thats 68.5mins including a fail on IHKA module

so far no issues will updates, once I manage to do rest will update the group

[shawnsheridan]

Originally Posted by pcp1234

sorry I was under impression that you wrote it
ok, i followed it and obviously selected connection via vin

in order not to repeat update version from to here - was F010-13-11-504 to F010-18-07-530

1. had 18modules to update so I started with ZGW, PDC and JBBF, that took approx 6mins
2. then i updated DSC2 and ICM, that took 7mins
3. FRM module took shy of 5mins

so far no issues will update once I manage to update rest

[dashti640]

Originally Posted by shawnsheridan

Hi Shawnsheridan, I need your help mate please, I was trying to add code 5A2 for LED headlights retrofit but I was getting this error on E-Sys
"No FP could be generated from FA "". [C002]
Not all elements of the FA were found in the FA2FP: SALAPA 5A2 [72]"

that's is the error message I was getting but I could easily add 552 for Adaptive LED code with no problem. please advise. cheers

[shawnsheridan]

Originally Posted by dashti640

Hi Shawnsheridan, I need your help mate please, I was trying to add code 5A2 for LED headlights retrofit but I was getting this error on E-Sys
"No FP could be generated from FA "". [C002]
Not all elements of the FA were found in the FA2FP: SALAPA 5A2 [72]"

that's is the error message I was getting but I could easily add 552 for Adaptive LED code with no problem. please advise. cheers

Do you currently have adaptive Xenon, but you got to LED without Adaptive?

[dashti640]

Originally Posted by shawnsheridan

Do you currently have adaptive Xenon, but you got to LED without Adaptive?

Hi,
no, its just normal Bi-Xenon i had on my car F06 2014 and already installed the LED Headlight done all the wiring and but won't accept the 5A2 code. i can change it to 552 and also change it back to 522.