[whyycharles]

I have a 2016 Bmw 340 Xdrive with LCI lights and no adaptive leds.

Here is a picture of my SVT Tree, Both my FLE [43] and FLE [44] the POL values are
00, 00, 00, 05, 00, 00, 06, 00, 00, 00

SO what do i change?

Thanks!

[whyycharles]

anyone ;[?

[naga9201]

My car is ActiveHybrid3 2013, i-step is F020_16_03_504.

How can I reduce the brightness of DRL during the daytime.
I already tried PWM_LEVEL_1 Werte=64 to 32, but no change.

[naga9201]

Anyone help me !

Thanks in advance.

[whyycharles]

anyone?

[whyycharles]

bump

[dbonyad]

Originally Posted by dmnc02

Just to be clear, the above coding is for EU-spec F30/31 LCI with the non-adaptive LED headlights.

Hi dmnc02

I have a 640d (F06) UK spec with the new facelifted LED headlights that are very similar to the 3-series lights. The 6-series community is nowhere near as active as this one, and you guys have solved a very similar issue.

My car has two FLE modules both with POLI1_Idx, POLI2_Idx, and POLI3_Idx.

I want to enable full angel eye brightness with headlights on, however, my POLI werte values are all:

01, 01, 0E, 01, 01, 01, 01, 01, 01, 01

So I have no idea which value to change! Please could you, or anyone, give me any suggestions? I'd be so so so grateful.

All of the coding guides for doing this on a 5-series or 6-series don't work as they are designed for cars before the FLE modules for LED headlights.

Thanks.

Davood

[dbonyad]

Originally Posted by dbonyad

Hi dmnc02

I have a 640d (F06) UK spec with the new facelifted LED headlights that are very similar to the 3-series lights. The 6-series community is nowhere near as active as this one, and you guys have solved a very similar issue.

My car has two FLE modules both with POLI1_Idx, POLI2_Idx, and POLI3_Idx.

I want to enable full angel eye brightness with headlights on, however, my POLI werte values are all:

01, 01, 0E, 01, 01, 01, 01, 01, 01, 01

So I have no idea which value to change! Please could you, or anyone, give me any suggestions? I'd be so so so grateful.

All of the coding guides for doing this on a 5-series or 6-series don't work as they are designed for cars before the FLE modules for LED headlights.

Thanks.

Davood

dmnc02 My CADF file is attached, if that helps.

[stu14t]

Try this value in POLI1_Idx , POLI2_Idx and POLI3_Idx

01, 01, 0D, 01, 01, 01, 01, 01, 01, 01

(Remember to code both the FLE's. There are two)

[dbonyad]

Originally Posted by stu14t

Try this value in POLI1_Idx , POLI2_Idx and POLI3_Idx

01, 01, 0D, 01, 01, 01, 01, 01, 01, 01

(Remember to code both the FLE's. There are two)

Thanks stu14t for the tip, I'll try it. How did you work that out?

[stu14t]

Originally Posted by dbonyad

Thanks stu14t for the tip, I'll try it. How did you work that out?

I've already done something similar on my F30. Each pair of hex figures correspond to the LED groups, such as DRL, side markers, eyebrows etc. The two digit hex code itself then corresponds to a particular setting for that group, which includes brightness, if it's ramped on and off and it's priority over other settings and groups. What I did was work out which pair corresponds the DRL on your F06 and change the setting from 43% brightness to 100% brightness using a preset code that already exists.

If it doesn't work, we may have to alter the priority over other settings

[dbonyad]

That worked amazingly! Thanks so much. I'm hoping now that they don't overheat, but given the dipped beam and angels operate independently for indefinite periods it should be ok. Also I guess they're designed to work in Dubai so in the U.K. I'd hope there should be enough cooling!

Thanks again.

[stu14t]

You should be OK. The code used does not exceed the normal parameters for the LED just stops them dimming when the main lights are switched on

[Nubarsol]

Please excuse me, if this has been answered already, but I went through all the pages and couldn't find a direct answer. Will this method work for a US model 2016 340i LCI w/non adaptive headlights, or is this strictly for the EU spec. I did notice that one of the posts in this thread mentioned that the EU and US spec are the same, but I don't know accurate that is.

[Almaretto]

Originally Posted by Nubarsol

Please excuse me, if this has been answered already, but I went through all the pages and couldn't find a direct answer. Will this method work for a US model 2016 340i LCI w/non adaptive headlights, or is this strictly for the EU spec. I did notice that one of the posts in this thread mentioned that the EU and US spec are the same, but I don't know accurate that is.

100% Halo can be coded with low beams, parking lamps, and welcome lights for all headlamps. The coding is just different whether you have settings in fem_body, TMS, or FLE.

[userix]

I have an f15 x5 2016 that I am trying to code for 100% halo led brightness with lowbeams on. I do have adaptive LED headlights and I have tried all the FLE coding modules with no luck. I don't have the earlier TMS module, only the newer FLE.

My car is US spec 2016 x5 F15 with adaptive led headlights.

Was anyone able to get the 100% halo brightness with lowbeams on adaptive led headlights for US spec vehicles?

[Almaretto]

Originally Posted by userix

I have an f15 x5 2016 that I am trying to code for 100% halo led brightness with lowbeams on. I do have adaptive LED headlights and I have tried all the FLE coding modules with no luck. I don't have the earlier TMS module, only the newer FLE.

My car is US spec 2016 x5 F15 with adaptive led headlights.

Was anyone able to get the 100% halo brightness with lowbeams on adaptive led headlights for US spec vehicles?

Coding is on F15 Cheat Sheet as well as in Launcher Cheat Codes.

[HZX540e]

Originally Posted by Almaretto

Coding is on F15 Cheat Sheet as well as in Launcher Cheat Codes.

I looked at the F15 coding sheet in the F15 coding thread and it does not contain information about the halo increase to 100%. Please point me in the right direction. I am trying to code the halos to 100% with low beam on my xenon F15, is that even doable?

[stu14t]

If you have the FLE modules you need to look at the DRL_idx Hex codes and the current codes for POLI1_Idx. There will be one pair of codes that will be different between the two. This should be the corresponding pair that controls the DLR halo's. The code that is in the DRL_idx is the one for 100% brightness and the one presently in the POLI1_idx will be the dimmed. Simply alter the pair in POLI1_Idx , POLI2_Idx and POLI3_Idx to match the DRL_idx pair.

This is just an example, Say the

DRL_idx reads 02, 02, 0E, 02, 02, 02, 02, 02, 02, 02 and the

POLI1_idx reads: 02, 02, 0F, 02, 02, 02, 02, 02, 02, 02.

The third pair controls the DRL halos. They are already at 100% with just DRL so substitute the 0F with the 0E in POLI1_Idx, POLI2_Idx and POLI3_Idx as they correspond with the three light switch positions. Hey presto 100% Halo with lights on.

The above is only an example and it may look different in your car and / or be a different pair.

If you have the older TMS modules, it is still possible but the hex codes are arranged a completely different way.

[Almaretto]

Originally Posted by HZX540e

I looked at the F15 coding sheet in the F15 coding thread and it does not contain information about the halo increase to 100%. Please point me in the right direction. I am trying to code the halos to 100% with low beam on my xenon F15, is that even doable?

For F15 with 552 LED Adaptive Headlamps:



I am guessing your Xenons have LHM / TMS. Coding would be in TMS. Instead of comparing DRL_Idx to POLI1_Idx, POLI2_Idx and POLI3_Idx, you look at Tagfahrlicht to Standlicht Modus 1, Standlicht Modus 2, Standlicht Modus 3; additionally, you can code Welcome Light 1.

EDIT: Reference for F8x

[HZX540e]

Originally Posted by Almaretto

For F15 with 552 LED Adaptive Headlamps:

[IMG]

View post on imgur.com

[/IMG]

I am guessing your Xenons have LHM / TMS. Coding would be in TMS. Instead of comparing DRL_Idx to POLI1_Idx, POLI2_Idx and POLI3_Idx, you look at Tagfahrlicht to Standlicht Modus 1, Standlicht Modus 2, Standlicht Modus 3; additionally, you can code Welcome Light 1.

Posting here for the benefit of the entire community Almaretto sent me the instructions below and they worked like a charm on the 2016 X5 40e, now the Halos are at 100% with DRL (which they were always), parking light and high beam. Thank you Almaretto you are amazing


Must change BOTH TMS Modules otherwise your car will look like it has a bruised eye or is winking

3005 Leuchtmittelmatrix 1, F8

Tagfahrlicht (German for daytime running light)
00 03 00 00 00 04 00 00 64 03 00 00 64 23 00 00 <-- this is the default value

Standlicht Modus 1 / 2 / 3
00 03 00 00 64 03 00 00 64 03 00 00 2E 24 00 00 (must change all three modus)

Welcome Light 1
00 03 00 00 64 03 00 00 64 03 00 00 2E 24 00 00 (optional)

Parklicht
00 03 00 00 00 03 00 00 64 03 00 00 2E 24 00 00 (optional for street side parking lamp)

Follow Me Home
00 03 00 00 64 03 00 00 64 03 00 00 2E 24 00 00 (optional)

Remote Light
00 03 00 00 64 03 00 00 64 03 00 00 2E 24 00 00 (optional)

So Corona rings are dimmed from 100% DRL to 46% with low beams (64 Hex = 100 Decimal; 2E Hex = 46 Decimal). If you want 100, you change to blue hex in Standlicht Modus 1, 2, & 3 to 64 to match Tagfahrlicht; or you can choose any other desired percentage (eg, 50 = 80%). Plus, you can also set 'Welcome', 'Follow me home', or 'Remote lights,' to the same or desired percentage. And, remember to change both TMS (1082/ 1083).

The only one I didn't do is the parklicht which controls the intensity of the street side parking light. I get hassled enough when I have either side on and they're only 46%, imagine the number of people knocking on my door from three blocks down to tell me my lights are on

[stu14t]

Originally Posted by HZX540e

Posting here for the benefit of the entire community Almaretto sent me the instructions below and they worked like a charm on the 2016 X5 40e, now the Halos are at 100% with DRL (which they were always), parking light and high beam. Thank you Almaretto you are amazing


in BOTH TMS Modules
3005 Leuchtmittelmatrix 1, F8

Tagfahrlicht (German for daytime running light)
00 03 00 00 00 04 00 00 64 03 00 00 64 23 00 00

Standlicht Modus 1 / 2 / 3
00 03 00 00 64 03 00 00 64 03 00 00 2E 24 00 00

Welcome Light 1
00 03 00 00 64 03 00 00 64 03 00 00 2E 24 00 00

Parklicht
00 03 00 00 00 03 00 00 64 03 00 00 2E 24 00 00

Follow Me Home
00 03 00 00 64 03 00 00 64 03 00 00 2E 24 00 00

Remote Light
00 03 00 00 64 03 00 00 64 03 00 00 2E 24 00 00

So Corona rings are dimmed from 100% DRL to 46% with low beams (64 Hex = 100 Decimal; 2E Hex = 46 Decimal). If you want 100, you change to blue hex in Standlicht Modus 1, 2, & 3 to 64 to match Tagfahrlicht; or you can choose any other desired percentage (eg, 50 = 80%). Plus, you can also set 'Welcome', 'Follow me home', or 'Remote lights,' to the same or desired percentage. And, remember to change both TMS (1082/ 1083).

The only one I didn't do is the parklicht which controls the intensity of the street side parking light. I get hassled enough when I have either side on and they're only 46%, imagine the number of people knocking on my door from three blocks down to tell me my lights are on

People with other models that use the TMS modules can also use the above information too to assist.

Good work and thanks for sharing