07-03-2020, 10:45 AM | #1 |
New Member
4
Rep 26
Posts
Drives: BMW 320i Touring (F31)
Join Date: Jun 2020
Location: Lincolnshire
|
Hi everyone,
I wanted to share what I've found. There is *a lot* about upgrading screen on EntryNav but not so much when it comes to EntryNav2. I decided to take a punt and buy an 8.8" screen from eBay and follow the same principles as the EntryNav in terms of Hardware: - Remove boot/trunk lining to driver side (I'm F31 so there is no convenient panel) - Disconnect the Battery Negative Terminal - Tie a rage in the boot/trunk catch just in case some external factor causes it to close - remove just the top part of the passenger side trim with a trim removal tool (the bit housing the 2 central air vents) - this is all a "snap in" part - you can unplug the switches and set the trim aside, or leave it dangling.... I did the latter as there is only 2 screws to deal with. - Undo the 2 T20 screws and lift out the screen - you may need to move the wire to give you some slack - once lifted out, turn the screen around and remove the connector - Place a cloth over your dash to protect your shiny new screen - Lay the screen face down on the cloth and insert the connector. - Pick up the screen, turn it around, and insert it into the retaining recesses - re insert and tighten up the 2 T20 screws - relocate the trim piece that you removed (insert the switch connectors if you removed them!) - reconnect up the battery negative terminal - replace the boot/trunk trim - Insert your ObD2 connector and power on the car, but not the engine! You will notice at this point that your new screen does not power on. - Open up your app of choice and locate the HU_NBT_EVO section (I used BIMMERCODE so this was just Headunit > Expert Mode) - change the following 3 parameters: i) 3001 EXBOX > DISPLAY_VARIANTE = breites_display ii) 3005 APIX_CID > CID_DISPLAY_SIZE = 8.8 iii) 3005 APIX_CID > CID_DISPLAY_RES = 1280x480 - Submit/commit the code change (in BimmerCode go back to HU_NBT_EVO screen where it lists the 3000 codes and tap code) - wait for it to submit the changes and reboot the ECU. - watch your new screen come to life in all its 8.8" glory - Enjoy The installation and coding is fairly simple, so I got from start to end in no time, and ended up only with a picture of the 6.5" screen before I started and the 8.8" screen after I had finished. BEFORE - 6.5" Screen [IMG]https://f30.bimmerpost.com/forums/at...8;d=1593791163[/IMG] AFTER - 8.8" Screen [IMG]https://f30.bimmerpost.com/forums/at...8;d=1593791166[/IMG] Full install took about 20-25 minutes. Last edited by f31shadow_lincs; 07-03-2020 at 10:54 AM.. |
07-29-2020, 12:36 AM | #2 |
Private
21
Rep 67
Posts |
Congratulations!
I know that NBT Evo and EntryNav2 are using Apix2 displays with lower voltage (~9v) while rest HU using Apix1 displays with higher voltage (~11v). They are no interchangeable, so did you buy Evo 8.8 screen or Apix1 8.8 and cable with voltage transformator? |
Appreciate
0
|
07-29-2020, 12:55 AM | #3 | |
New Member
4
Rep 26
Posts
Drives: BMW 320i Touring (F31)
Join Date: Jun 2020
Location: Lincolnshire
|
Quote:
Incidentally it was a touch model too, so I have also been able to code that in as well! |
|
Appreciate
1
SniPro20.50 |
09-30-2020, 10:48 PM | #4 |
Private
21
Rep 67
Posts |
I’ve seen somewhere that touch is not supported on Entrynav2, what you say is opposite. Good news!
|
Appreciate
0
|
10-10-2020, 01:21 PM | #5 | |
Private
21
Rep 67
Posts |
Quote:
Thanks in advance, |
|
Appreciate
0
|
01-22-2024, 05:17 PM | #6 |
New Member
2
Rep 7
Posts |
Should be this one https://www.realoem.com/bmw/enUS/par...&q=65508709339
I am looking for same solution , I have an Entrynav2 , F31, 7/2017 |
Appreciate
0
|
Post Reply |
Bookmarks |
|
|