03-04-2019, 02:04 PM | #1 |
Major
873
Rep 1,079
Posts |
Removing(ONLY COVER) F32 Antenna/Shark Fin Carbon Fiber Cover/Cap
I've ordered CF shark fin/antenna cover for my car and wanted to know if anyone has successfully removed it after install without damaging the underlying antenna/fin and the paint?
I believe it is supposed to be attached using 3M double-sided tape. Any suggestions are appreciated. I'll also be installing the M4 style CF trunk spoiler, any info about removing that successfully would also be helpful. Thank You. |
03-04-2019, 02:28 PM | #2 |
David
786
Rep 2,010
Posts |
I've never done the antenna but have done spoilers in the past. but removing 3m tape off paint causes no harm, heat up the area prior to removal though (hair dryer or low heat on a heat gun), and use a paint safe adhesive remover afterwards.
|
Appreciate
0
|
03-04-2019, 04:06 PM | #3 |
Major
873
Rep 1,079
Posts |
I'm just worried because of the weird shape of the antenna/fin cover, I will have to just pull out evenly after heating without pulling off the antenna/fin too
|
Appreciate
0
|
03-12-2019, 12:04 PM | #4 |
Lieutenant
370
Rep 552
Posts |
You need to tape around the fin against the roof, then use a razor to cut the rubber gasket holding the fin on. Heat will not remove the fin since rubber is holding it on. To seal it back on, highly recommend using a silicone industrial strength weatherproof sealant (used with windows). Do not use a strong sealant from Autozone to put the new one on (learned my lesson, was too weak to bond correctly). You can try the 3m tape it comes with, but I don't really trust whatever they include from China. If water gets in there, replacement can get pretty expensive.
Had this done when my roof was wrapped gloss black and haven't had any issues with leaking or water in antenna. Last edited by mlev; 03-12-2019 at 12:09 PM.. |
Appreciate
0
|
03-12-2019, 12:11 PM | #5 | |
Major
873
Rep 1,079
Posts |
Do I need to remove the fin?
Quote:
|
|
Appreciate
0
|
03-13-2019, 09:21 AM | #6 | ||
Lieutenant
370
Rep 552
Posts |
Quote:
|
||
Appreciate
0
|
03-19-2019, 09:26 AM | #7 | |
Major
873
Rep 1,079
Posts |
Quote:
Did you get the roof wrapped? If so then how's your experience with it? |
|
Appreciate
0
|
03-19-2019, 11:57 AM | #8 | |
Lieutenant
370
Rep 552
Posts |
Quote:
Last edited by mlev; 03-19-2019 at 12:06 PM.. |
|
Appreciate
0
|
03-19-2019, 01:56 PM | #9 | |
Major
873
Rep 1,079
Posts |
Quote:
|
|
Appreciate
0
|
03-19-2019, 03:29 PM | #10 | |
Lieutenant
370
Rep 552
Posts |
Quote:
Got the roof wrapped 6 months ago. The installer preferred the Avery and it's what he had in stock and used for all his wraps, so I did my research and felt comfortable with using that over the 3M. You can't go wrong with either as long as the installer does a good job. |
|
Appreciate
0
|
03-19-2019, 04:22 PM | #11 | |
Major
873
Rep 1,079
Posts |
Quote:
I read the roof vinyl should be replaced every 3 years, otherwise it gets hard to remove and leaves some yellowish tint in some cases. $300 for 3 years is not a bad deal. What kind of black wheels do you have? Might powder-coat my 400Ms. |
|
Appreciate
0
|
03-19-2019, 04:56 PM | #12 | |
Lieutenant
370
Rep 552
Posts |
Quote:
To install my lip, small self tapping screws were used under the bumper to ensure it stays attached properly. Even if it was removed, you wouldn't be able to see the holes so not a big deal. I don't know how you would attach any lips securely without screws. I'm lowered on H&R sport springs and have scraped quite a few times, making me glad it's screwed in (no movement of bumper and no visible damage to lip). That thing needs to be able to withstand a lot, especially driving 80mph on the highway with the wind force. The older and lower quality vinyl wraps should be replaced every 3 years. I've also read that the metallic/specialty wraps only last about 3 years. Black/white is much more durable. If you're more worried about your paint underneath, you just need to take care of it and do your best to keep it out of the sun when possible. If you park out in the sun and heat all day every day, 3 years would be a safe bet. But even then, the paint will probably look fantastic underneath. I couldn't find any reviews saying SW900 or 1080 messed up their paint after only 3-4 years, when applied properly. You have to keep in mind that good quality wrap actually protects the paint underneath, moreso than being exposed to the elements during that time. I'm sure your installer can give you some more insight as well. At least you won't have to worry about 1080 or SW900 wrap fading or discoloring, like good window tint it's got great UV protection built in. 1080's gloss black claims "The film is coated with a UV protective layer which lasts up to 7 years outdoors." And Avery claims "up to" 12 years for their black. edit: correction on installing the lip. You can use the pre-drilled holes from the bolts already in the bumper, but my installer added self-tapping screws on top of that. Last edited by mlev; 03-19-2019 at 06:21 PM.. |
|
Appreciate
0
|
03-19-2019, 05:04 PM | #13 | |
Major
873
Rep 1,079
Posts |
Quote:
How hard was it to attach the front lip? Did you do it yourself? I'm thinking of gettting Dinan springs with bump stops, the shops charge a lot for installing springs over here, the roads here are not so good and my girlfriend's garage has a big slope, it might be fine as she never scraped her Civic Type R which is pretty low in stock form, she does have to go very slow over there. I can't find the silver/black 437Ms, do you have any picture? All I see are complete black ones. |
|
Appreciate
0
|
03-19-2019, 05:11 PM | #14 | |
Lieutenant
370
Rep 552
Posts |
Quote:
Some pics of my wrap + wheels + lip. I had someone install the lip for pretty cheap, he just jacked up the front, lined it up and started installing the screws. I could've done it myself but didn't mind paying a bit |
|
Appreciate
0
|
03-20-2019, 11:27 AM | #15 | |
Major
873
Rep 1,079
Posts |
Quote:
Is that a matte black lip? Where did you get it from and how's the fitment? Are there different types of front splitters/lips? Apart from different material, I heard carbon fiber lip breaks easily on small impacts. Also, how is your experience with lowering springs? How long have you had them for? |
|
Appreciate
0
|
03-20-2019, 12:28 PM | #16 | |
Lieutenant
370
Rep 552
Posts |
Quote:
I chose a polyurethane (dense black gloss plastic) for that reason. They don't crack like carbon fiber does, plus CF is usually much more expensive. For example, I had my brakes changed the other day and the installer test drove my car. He pulled right up to a median and hit it with my lip. I got out, wiped the white concrete dust off my lip, and it looked good as new. I am certain that would have cracked a CF lip. Car has been lowered for about 5 months. I love the look, H&R sport springs really give the perfect stance. But obviously suspension is stiffer and a bit bumpier being lower to the ground. It's a sacrifice I'm willing to make for now, but down the road may put on Koni Yellow or possibly Bilstien B8's. I've heard the Koni Yellow's are very comfortable with Dinan Springs or something similar. With M Sport shocks and H&R sport springs, potholes can be rough/loud if you hit them. Car handles great though and I am happy with just the H&R's for the time being |
|
Appreciate
0
|
Post Reply |
Bookmarks |
Tags |
435 coupe, antenna, carbon fiber, f32, shark fin, tape |
Thread Tools | Search this Thread |
|
|