[DJSF3014]

Originally Posted by 320if30

What if you do not have lane departure warning on car. I added heated msport wheel (car was standard with msport), button and module. coded via bimmercode and light comes on button but no heat. The module does have another single wire coming off it with no place to go. I assume this would be for vibrator? please help.

Yes that is where it would go. Did you ensure you bought a heated steering wheel? That's the only thing that would make sense I do believe that just the heating element would work without the vibrations assist.

[320if30]

Originally Posted by DJSF3014

Yes that is where it would go. Did you ensure you bought a heated steering wheel? That's the only thing that would make sense I do believe that just the heating element would work without the vibrations assist.

It is for sure a heated wheel. Should I shut off the vibrate in Bimmercode?
I feel like its in my head that the wheel gets somewhat warm, but I just don't know. I feel my brothers F80 wheel and it is very warm. You would think since the light is working that it should heat the wheel either way.

any help would be much appreciated.

this is what i coded

FEM_BODY
3140 PFLinSteeringWheel
CODDT_BYTE_00_SZL_LIN = LHZ_aktiv
LIN_VARIANTE_LRE = lre_tlc_lhz
LIN_VARIANTE_SZL = szl_4Band
LRE_Verbaut = aktiv

[DJSF3014]

Originally Posted by 320if30

It is for sure a heated wheel. Should I shut off the vibrate in Bimmercode?
I feel like its in my head that the wheel gets somewhat warm, but I just don't know. I feel my brothers F80 wheel and it is very warm. You would think since the light is working that it should heat the wheel either way.

any help would be much appreciated.

this is what i coded

FEM_BODY
3140 PFLinSteeringWheel
CODDT_BYTE_00_SZL_LIN = LHZ_aktiv
LIN_VARIANTE_LRE = lre_tlc_lhz
LIN_VARIANTE_SZL = szl_4Band
LRE_Verbaut = aktiv

I don't know about the coding but I would code out vibration just to cancel that as a possibility also the heating element controller could have gone bad multiple threads about that.

[320if30]

Originally Posted by DJSF3014

I don't know about the coding but I would code out vibration just to cancel that as a possibility also the heating element controller could have gone bad multiple threads about that.

Controller, as in the Module? black box

[DJSF3014]

Originally Posted by 320if30

Controller, as in the Module? black box

Yes that entire thing has been known to fail and you gotta get a new one.

[320if30]

Originally Posted by DJSF3014

Yes that entire thing has been known to fail and you gotta get a new one.

Crap. well that sucks. I bought off ebay.

thank you for your help

[DJSF3014]

Originally Posted by 320if30

Crap. well that sucks. I bought off ebay.

thank you for your help

Sent you a pm.

[320if30]

Originally Posted by doughboy

I bought a 4 way plug then I can plug the heater controller into that via it's black 4 way socket that would normally go into A83*4B plug.

Then via new leads (made from pin and socket tails soldered back to back) from the 4 way to the to the yellow 6 way airbag connector pins 1&3.

Will solder later and heatshrink it up. Just need some time to fit it now...

Thanks

what does the single black wire connect to? Can someone please confirm this?

[320if30]

Originally Posted by 320if30

what does the single black wire connect to? Can someone please confirm this?

figured it out. it needs to be jumped to the blue wire on RH side. Either direct into SZL or at controls.
BIG THANKS TO HAWKO!!!