[shawnsheridan]

Originally Posted by Justin Gang

Hello Mr.Shawnsheridan,

I have a few enquirys.

I added with Sports Gear Stick and Sports Handle with paddles. And then i did vo code and activated action for paddle.

I wonder that do i need to set FA back to original when i make the flash in Esys with older psdzdata 55.0.100 although installed parts is not disassemble and assemble to origianl parts.

Thank you in advance.

Not sure I understand what you ask. FA needs to support the hardware no matter what PSdZData version you use.

[Justin Gang]

Originally Posted by shawnsheridan

Not sure I understand what you ask. FA needs to support the hardware no matter what PSdZData version you use.

Hi Shawn,

I have other question.

I would update the ASD with psdzdata 54.0 which is not trimmed because the ASD does not working. I bought as used part. Such as the reason, I have been searching that file for 2 months. but it was hard to find it and download. the reason i want 54.0 verison is for hearing N57D and M3, M4 engine sound. I have decided to flash ASD ecu after reffed to your advice.

[a few questions]
☞Which version needs for using the pdszdata 54.0 full?
☞I heard that Launcher Pro 3 is supported Esys version by 3.27.1 to 3.31.0. but I know that i need older 3.26.1 to use the pdszdata 54.0 full. I installed Launcher Pro 3 with Esys 3.27.1

Please let you know how to deal this for me and share me.

Thank you for reading me.
Best Regards

[shawnsheridan]

Originally Posted by Justin Gang

Hi Shawn,

I have other question.

I would update the ASD with psdzdata 54.0 which is not trimmed because the ASD does not working. I bought as used part. Such as the reason, I have been searching that file for 2 months. but it was hard to find it and download. the reason i want 54.0 verison is for hearing N57D and M3, M4 engine sound. I have decided to flash ASD ecu after reffed to your advice.

[a few questions]
☞Which version needs for using the pdszdata 54.0 full?
☞I heard that Launcher Pro 3 is supported Esys version by 3.27.1 to 3.31.0. but I know that i need older 3.26.1 to use the pdszdata 54.0 full. I installed Launcher Pro 3 with Esys 3.27.1

Please let you know how to deal this for me and share me.

Thank you for reading me.
Best Regards

I do not keep older versions of PSdZData. If you get 54.0 Full, and need older E-Sys, send me a PM.

[jalami]

I have nbt retrofit. I can perform flash. (retrofit with fsc).?
I need a battery charger, some specific.?
Thanks advance.

[outubro]

I have this error with kafas2 I am just doing the ugrade of kafas can help me.
please
TAL execution started.
ExecutionID=2018/12/02-17:09:25.348
[] prepareTALExecution started
[] prepareTALExecution finished
[] prepareVehicleForFlash started
MCDDiagService<id=20600, job=com.bmw.psdz.jobs.common.MCD3_PrepareVehicleFo rFlash, service=CC, description=error: negative response : conditionsNotCorrect, link=#RtGen_MultipleEcuJob_LogicalLink>
MCDDiagService<id=20600, job=com.bmw.psdz.jobs.common.MCD3_PrepareVehicleFo rFlash, service=CC, description=error: negative response : conditionsNotCorrect, link=#RtGen_MultipleEcuJob_LogicalLink>
MCDDiagService<id=76600, job=com.bmw.psdz.jobs.common.MCD3_PrepareVehicleFo rFlash, service=RC_SEM, description=error: negative response : conditionsNotCorrect, link=#RtGen_MultipleEcuJob_LogicalLink>
MCDDiagService<id=76600, job=com.bmw.psdz.jobs.common.MCD3_PrepareVehicleFo rFlash, service=RC_SEM, description=error: negative response : conditionsNotCorrect, link=#RtGen_MultipleEcuJob_LogicalLink>
[] prepareVehicleForFlash finished
[KAFAS2 - 5D] There was an error during TAL execution, please check the log files.
[KAFAS2 - 5D] - [Exception - KAFAS2 - 5d] SVK-Ist does not match expected SGBMIDs for ecu ECUId:KAFAS2_0x5D. Excpected (relevant process classes only): [hwel_00000fb7-000_010_001], Actual (relevant process classes only): [hwel_00000bd0-000_005_001], Missing SGBMID(s): [hwel_00000fb7-000_010_001], Surplus SGBMID(s): [hwel_00000bd0-000_005_001]
[KAFAS2 - 5D] installECUBL started
[KAFAS2 - 5D] installECUBL finished
[KAFAS2 - 5D] finalizeECUBLUpdate started
[KAFAS2 - 5D] finalizeECUBLUpdate finished
[] finalizeVehicleFlash started
[] finalizeVehicleFlash finished
[] finalizeVehicleCoding started
[] finalizeVehicleCoding finished
[] finalizeTALExecution started
[] finalizeTALExecution finished
TAL execution finished
TAL-Execution finished with status: "FinishedWithError". [C207]
TAL execution finished. Duration: "1min 8s". [C206]

[shawnsheridan]

Originally Posted by outubro

I have this error with kafas2 I am just doing the ugrade of kafas can help me.
please
TAL execution started.
...
[KAFAS2 - 5D] - [Exception - KAFAS2 - 5d] SVK-Ist does not match expected SGBMIDs for ecu ECUId:KAFAS2_0x5D...

Wrong I-Step Shipment. I replied to your same PM.

[outubro]

Originally Posted by shawnsheridan

Wrong I-Step Shipment. I replied to your same PM.

ok i ugrad_kafas2 tho cafd_00001148_000_030_004 but I still have the same problem
I do not have the HBA to work.
I have a camera error.
I do not know if this CAFD is the best.

[shawnsheridan]

Originally Posted by outubro

ok i ugrad_kafas2 tho cafd_00001148_000_030_004 but I still have the same problem
I do not have the HBA to work.
I have a camera error.
I do not know if this CAFD is the best.

I have no idea what you have going on with your Retrofit, but if you have CAFD with Green Dot, then CAFD is good.

[outubro]

Originally Posted by shawnsheridan

I have no idea what you have going on with your Retrofit, but if you have CAFD with Green Dot, then CAFD is good.

yes the CAFD is green, the camera kafas does hba?
I do not need another camera.

[shawnsheridan]

Originally Posted by outubro

yes the CAFD is green, the camera kafas does hba?
I do not need another camera.

KAFAS Camera supports HBA. New SZL Stalk is also needed, and proper coding.

[outubro]

Originally Posted by shawnsheridan

KAFAS Camera supports HBA. New SZL Stalk is also needed, and proper coding.

Yes, I also have the new SLZ.
What is the encoding for slz?

can help

[shawnsheridan]

Originally Posted by outubro

Yes, I also have the new SLZ.
What is the encoding for slz?

can help

No, sorry. I never retrofit neither SZL nor KAFAS myself.

[outubro]

Originally Posted by shawnsheridan

No, sorry. I never retrofit neither SZL nor KAFAS myself.

the slz is inside FEM_BOY ?

[shawnsheridan]

Originally Posted by outubro

the slz is inside FEM_BOY ?

Inside FEM?

This is SZL:

[outubro]

Originally Posted by shawnsheridan

Inside FEM?

This is SZL:

Attachment 1947863

No, this was the old one.
now I have the new one from 01/03/2017 with hba
i have car 2015

[shawnsheridan]

Originally Posted by outubro

No, this was the old one.
now I have the new one from 01/03/2017 with hba
i have car 2015

Ok. The picture though was not to denote the exact SZL you have, rather just denote what an SZL was, as you asked if it were in in FEM_BDOY.

Anyway, good luck with retrofit.

[outubro]

Originally Posted by shawnsheridan

Ok. The picture though was not to denote the exact SZL you have, rather just denote what an SZL was, as you asked if it were in in FEM_BDOY.

Anyway, good luck with retrofit.

then what it is necessary to do to function

[shawnsheridan]

Originally Posted by outubro

then what it is necessary to do to function

As I wrote above:

Originally Posted by shawnsheridan

No, sorry. I never retrofit neither SZL nor KAFAS myself.

I have no idea why your HBA is not working.

[Maxfusion]

I have an error on flashing retrofitted NBT Evo Touch.

Log:

Read SVT before TAL execution started.


TAL execution started.

ExecutionID=2019/03/13-10:08:40.712

[] prepareTALExecution started [PROGRESS]

[] prepareTALExecution finished [PROGRESS]

[] prepareVehicleForFlash started [PROGRESS]

MCDDiagService<id=20600, job=com.bmw.psdz.jobs.common.MCD3_PrepareVehicleFo rFlash, service=CC, description=error: negative response : conditionsNotCorrect, link=#RtGen_MultipleEcuJob_LogicalLink> [DIAGSERVICE]

MCDDiagService<id=20600, job=com.bmw.psdz.jobs.common.MCD3_PrepareVehicleFo rFlash, service=CC, description=error: negative response : conditionsNotCorrect, link=#RtGen_MultipleEcuJob_LogicalLink> [DIAGSERVICE]

MCDDiagService<id=20600, job=com.bmw.psdz.jobs.common.MCD3_PrepareVehicleFo rFlash, service=CC, description=error: negative response : conditionsNotCorrect, link=#RtGen_MultipleEcuJob_LogicalLink> [DIAGSERVICE]

MCDDiagService<id=20600, job=com.bmw.psdz.jobs.common.MCD3_PrepareVehicleFo rFlash, service=CC, description=error: negative response : conditionsNotCorrect, link=#RtGen_MultipleEcuJob_LogicalLink> [DIAGSERVICE]

MCDDiagService<id=20600, job=com.bmw.psdz.jobs.common.MCD3_PrepareVehicleFo rFlash, service=CC, description=error: negative response : conditionsNotCorrect, link=#RtGen_MultipleEcuJob_LogicalLink> [DIAGSERVICE]

MCDDiagService<id=76600, job=com.bmw.psdz.jobs.common.MCD3_PrepareVehicleFo rFlash, service=RC_SEM, description=error: negative response : conditionsNotCorrect, link=#RtGen_MultipleEcuJob_LogicalLink> [DIAGSERVICE]

MCDDiagService<id=76600, job=com.bmw.psdz.jobs.common.MCD3_PrepareVehicleFo rFlash, service=RC_SEM, description=error: negative response : conditionsNotCorrect, link=#RtGen_MultipleEcuJob_LogicalLink> [DIAGSERVICE]

MCDDiagService<id=76600, job=com.bmw.psdz.jobs.common.MCD3_PrepareVehicleFo rFlash, service=RC_SEM, description=error: negative response : conditionsNotCorrect, link=#RtGen_MultipleEcuJob_LogicalLink> [DIAGSERVICE]

MCDDiagService<id=76600, job=com.bmw.psdz.jobs.common.MCD3_PrepareVehicleFo rFlash, service=RC_SEM, description=error: negative response : conditionsNotCorrect, link=#RtGen_MultipleEcuJob_LogicalLink> [DIAGSERVICE]

MCDDiagService<id=76600, job=com.bmw.psdz.jobs.common.MCD3_PrepareVehicleFo rFlash, service=RC_SEM, description=error: negative response : conditionsNotCorrect, link=#RtGen_MultipleEcuJob_LogicalLink> [DIAGSERVICE]

[] prepareVehicleForFlash finished [PROGRESS]

MCDDiagService<id=230900, job=com.bmw.psdz.jobs.common.MCD3_ActivateProgMode Cascade, service=DSC - DiagnosticSessionControl, description=error: timeout, link=HU_ENTRYNAV_63_ETHERNET_63> [DIAGSERVICE]

MCDDiagService<id=230900, job=com.bmw.psdz.jobs.common.MCD3_ActivateProgMode Cascade, service=DSC - DiagnosticSessionControl, description=error: timeout, link=HU_ENTRYNAV_63_ETHERNET_63> [DIAGSERVICE]

MCDDiagService<id=230900, job=com.bmw.psdz.jobs.common.MCD3_ActivateProgMode Cascade, service=DSC - DiagnosticSessionControl, description=error: timeout, link=HU_ENTRYNAV_63_ETHERNET_63> [DIAGSERVICE]

MCDDiagService<id=242900, job=com.bmw.psdz.jobs.common.MCD3_ActivateProgMode Cascade, service=RC_SDB - RoutineControl SetDefaultBus, description=error: timeout, link=HU_ENTRYNAV_63_ETHERNET_63> [DIAGSERVICE]

[] Activate programming mode was not successful for: ECUId:HU_ENTRYNAV_0x63 [WARN]

[] ECUId:HU_ENTRYNAV_0x63 not accessible cause could not be switched to parallel programming mode [WARN]

[HU_ENTRYNAV - 63] ECUId:HU_ENTRYNAV_0x63 not accessible cause could not be switched to parallel programming mode [THROWABLE]

[] ECUId:HU_ENTRYNAV_0x63 not accessible cause could not be switched to parallel programming mode [WARN]

[] finalizeVehicleFlash started [PROGRESS]

[] finalizeVehicleFlash finished [PROGRESS]

[] prepareVehicleForCoding started [PROGRESS]

[] prepareVehicleForCoding finished [PROGRESS]

[] finalizeVehicleCoding started [PROGRESS]

[] finalizeVehicleCoding finished [PROGRESS]

[] finalizeTALExecution started [PROGRESS]

[] finalizeTALExecution finished [PROGRESS]

TAL execution finished [TAL_EXECUTION_FINISHED]

TAL-Execution finished with status: "FinishedWithError". [C207]

TAL execution finished. Duration: "2min 30s". [C206]


Read SVT after TAL execution started.

Read SVT after TAL execution finished.


Doing all with the ECU Flashing guide 1.01
E-sys 3.27 place this errors, E-sys 3.30 don`t allow to check boxes BlFlash, SwDeploy, CdDeploy, IbaDeploy.

[shawnsheridan]

Originally Posted by Maxfusion

I have an error on flashing retrofitted NBT Evo Touch.

Log:
...
[] Activate programming mode was not successful for: ECUId:HU_ENTRYNAV_0x63 [WARN]

[] ECUId:HU_ENTRYNAV_0x63 not accessible cause could not be switched to parallel programming mode [WARN]

Assuming you are using ENET Cable, did you move Ethernet from Quadlock to OABR?

[Ibo24]

Originally Posted by shawnsheridan

PM sent.

Could you please send me that to, how to configure tfd32. Might come in handy when I would flash my KOMBI, FEM_GW.

[shawnsheridan]

Originally Posted by Ibo24

Could you please send me that to, how to configure tfd32. Might come in handy when I would flash my KOMBI, FEM_GW.

PM sent.