04-21-2019, 08:26 PM | #45 |
Second Lieutenant
105
Rep 225
Posts |
Thanks for posting. That's a good video! Also good to see that the AFR says low as the failsafe kicks in. So I take it your MHD tune is working OK with your turbo?
__________________
16 M235 Cabrio - BM3, ER CP, Wagner DP & IC, Dinan Intake, MPE, Torqbyte CM5
18 340i F30 mostly stock |
Appreciate
0
|
04-21-2019, 10:57 PM | #46 |
Colonel
1076
Rep 2,354
Posts |
I was running a MHD PS2 BETA-map in the video. My tuner is still working on my custom map. So far the BETA-map is working great but only made for 91 pump so not really super powerful.
__________________
M135i 8AT PWG, MHD, Pure Stage2, WMI via Torqbyte CM5-LT, Custom tuned by PureBoost
(A Dane in China) |
Appreciate
0
|
09-22-2019, 05:51 PM | #47 | |
ECUTek Master Tuner
10438
Rep 1,728
Posts
Drives: F80 M3 YMB
Join Date: Jul 2017
Location: Colorado Springs
|
Thank you for posting this how to. I will be using it for my meth install on my F80
Are you still not running an anti-siphon solenoid and instead running the 20 psi check valve?
__________________
Quote:
|
|
Appreciate
0
|
09-22-2019, 08:22 PM | #48 |
Colonel
1076
Rep 2,354
Posts |
I had a solenoid before with the BMS kit but it is just another component to fail. You loose a bit of flow with the check valve but it is more reliable.
__________________
M135i 8AT PWG, MHD, Pure Stage2, WMI via Torqbyte CM5-LT, Custom tuned by PureBoost
(A Dane in China) |
Appreciate
0
|
09-22-2019, 09:08 PM | #49 | |
ECUTek Master Tuner
10438
Rep 1,728
Posts
Drives: F80 M3 YMB
Join Date: Jul 2017
Location: Colorado Springs
|
Thank you. I like the lack of the solenoid, it simplifies the system.
__________________
Quote:
|
|
Appreciate
0
|
12-06-2019, 03:25 AM | #51 | |
Colonel
1076
Rep 2,354
Posts |
Quote:
Good you mention it. I have not cleaned mine for +2 years or so
__________________
M135i 8AT PWG, MHD, Pure Stage2, WMI via Torqbyte CM5-LT, Custom tuned by PureBoost
(A Dane in China) |
|
Appreciate
0
|
12-06-2019, 08:57 AM | #52 |
First Lieutenant
115
Rep 340
Posts |
But on the bms stealth tank.. The connection before the pump is so short.. How can you even fit the filter in.. I have the bms tank and planning to put the filter after the pump as well
|
Appreciate
0
|
12-06-2019, 09:25 PM | #53 |
Colonel
1076
Rep 2,354
Posts |
Sorry, I dont know the stealth tank. I believe you can get a in-tank pickup filter....but that will probably not be accessible hmm. Just put the filter where you can then.
__________________
M135i 8AT PWG, MHD, Pure Stage2, WMI via Torqbyte CM5-LT, Custom tuned by PureBoost
(A Dane in China) |
Appreciate
0
|
03-10-2020, 10:22 PM | #54 |
New Member
10
Rep 28
Posts |
This is a great thread and thanks for sharing your setups! I'm looking into the torqbyte setup for my N55 M2.
I have the Fuel-It direct port methanol kit installed which uses (6) 550cc injectors. Does the torqbyte controller have 6 GPO's or must you splice the injector wires together? Also, will the boost solenoid failsafe work with the EWG N55?
__________________
2017 BMW M2 in Mineral Gray DCT Transmission
Speedtech Stg 3 (8374) l BM3 Jordan Tuned l ER Chargepipe l ER FMIC l Stage 3 LPFP l EOS Pump Controller l Dorch Stage 2 HPFP l NGK 97506 l JRZ RS Two l SPL Suspension Parts l RE-71 R’s l BMW M Performance Kidney Grills, Mirror Covers, Spoiler, Rear Valence l Full PPF Wrap l 35% Tint l |
Appreciate
0
|
03-11-2020, 03:04 AM | #55 | |
Colonel
1076
Rep 2,354
Posts |
Quote:
Have fun
__________________
M135i 8AT PWG, MHD, Pure Stage2, WMI via Torqbyte CM5-LT, Custom tuned by PureBoost
(A Dane in China) |
|
Appreciate
0
|
03-11-2020, 09:44 AM | #56 |
New Member
10
Rep 28
Posts |
Sounds good thanks for the information. I’ve been emailing with Alex at Torqbyte and will ask about the GPO amperage. Otherwise I think this controller can be a good solution for my system.
|
Appreciate
0
|
03-14-2020, 10:21 PM | #57 | |
Captain
347
Rep 801
Posts |
Quote:
|
|
Appreciate
0
|
05-29-2022, 08:30 AM | #58 | |
New Member
9
Rep 9
Posts |
Quote:
My ~5 year old DDP 5800 (1.3gph, 12v, 200psi) from BMS with 100% duty draws around 10 amps vs 6amps i saw in harkes video. with 50% duty I get around 6 amps. Dosent matter if solenoid is open or closed, amps are about the same. I get meth flow. Nozzle is a BMS CM7 Pump starts to fail, small blockage in line (meth line compressed some how) ? I rembember when system was installed the duty and amp reading were in the same range as in the video.
__________________
10.93 @ 200kmh
|
|
Appreciate
0
|
Post Reply |
Bookmarks |
|
|