10-29-2015, 07:21 PM | #155 |
Captain
252
Rep 674
Posts |
|
Appreciate
0
|
10-30-2015, 01:27 PM | #157 |
Brigadier General
925
Rep 3,089
Posts |
I dont think it would be worth spending the money. This swap was entirely for looks.
__________________
|
Appreciate
0
|
10-30-2015, 05:03 PM | #158 | |
First Lieutenant
93
Rep 390
Posts |
Quote:
Good luck.
__________________
Best,
Charlie 2013 328i MSport Estoril Blue, 6spd MT, Premium, Tech & Drivers Assist +, Bavsound Stage One/Ghost, Bimmertech Amp |
|
Appreciate
0
|
10-31-2015, 08:57 AM | #159 |
Captain
252
Rep 674
Posts |
As stated before, I used the existing hangers and rubber bushings. No alterations to the mounting hardware were necessary.
|
Appreciate
0
|
10-31-2015, 09:25 AM | #160 | |
First Lieutenant
93
Rep 390
Posts |
Quote:
__________________
Best,
Charlie 2013 328i MSport Estoril Blue, 6spd MT, Premium, Tech & Drivers Assist +, Bavsound Stage One/Ghost, Bimmertech Amp |
|
Appreciate
0
|
10-31-2015, 10:45 AM | #161 |
Brigadier General
925
Rep 3,089
Posts |
You dont need the hangers but on the right side the horizonal rod attached to the muffler that fits into the rubber is too short. It wont reach all the way through the rubber piece. My shop ended up cutting off the rod and welding on a longer piece.
__________________
|
Appreciate
0
|
11-01-2015, 09:15 AM | #162 | |
Colonel
3179
Rep 2,577
Posts |
Quote:
At low RPM when valve is closed, the exhaust flow doesn't have to travel all the way to left side, which will either translate to a loss at low end or faster spool up or both. At high end, flow is certainly less restrictive. N20 will see gains if stock setup is truly restrictive for the power, or the flow turbo/engine makes, which is the case with a tune.
__________________
Lemania 2320
|
|
Appreciate
0
|
11-01-2015, 04:30 PM | #163 |
Captain
252
Rep 674
Posts |
Mine was the same way but I've never had an issue with it falling off.
|
Appreciate
0
|
12-03-2015, 10:16 PM | #165 |
Captain
149
Rep 674
Posts |
There are at least a couple of people that have done it to non-M sports, just search the forum. I almost started that way and then realized the 328i base model bumper had to be trimmed and I had only seen one diffuser that would fit on the existing bumper to make it look right. Not sure that even exist any longer.
|
Appreciate
0
|
05-28-2016, 10:03 PM | #166 |
New Member
3
Rep 14
Posts |
Hello,guys:
I was change my muffler again, this time I choose Remus exhaust for 35i uses. this installation: http://hoita.blogspot.tw/2016/05/f32...i-exhaust.html video: |
Appreciate
0
|
09-13-2016, 09:06 AM | #168 |
Brigadier General
925
Rep 3,089
Posts |
Yes but you may want to extend the right side hanger a bit so that it fully seats in the rubber piece. My exhaust guy just welded on an extra length metal rod.
__________________
|
Appreciate
0
|
09-14-2016, 08:44 PM | #171 | |
First Lieutenant
93
Rep 390
Posts |
Quote:
__________________
Best,
Charlie 2013 328i MSport Estoril Blue, 6spd MT, Premium, Tech & Drivers Assist +, Bavsound Stage One/Ghost, Bimmertech Amp |
|
Appreciate
0
|
09-16-2016, 10:15 AM | #175 | |
Brigadier General
925
Rep 3,089
Posts |
Quote:
Check out my build thread. I have a detailed post on when I did this mod.
__________________
|
|
Appreciate
0
|
09-18-2016, 01:19 PM | #176 | |
Private
11
Rep 66
Posts |
Quote:
Does anybody know if exhaust tips are included with 18302354340? If not- does anybody have suggestion of any? BMS wont fit MPE they say :/ |
|
Appreciate
0
|
Post Reply |
Bookmarks |
|
|