[Kevin_Trxn]

Please link me to the thread if this exists, but I'm looking for a new set of wheels and there are a ton of scattered threads for specs and fitment. I want a master thread where there are proper specs and photos! No gatekeeping
I also tried to search on mobile and went down 20 pages deep hoping to find the thread I'm looking for. Either I'm blind or it doesn't exist…

I want to see aftermarket wheels! Track/meaty setups to stanced/slammed setups.

Please don't post OEM wheels there's plenty of info on these out there.

Rules for posting:
1. Wheel Make:
2. Wheel Model:
3. Front Wheel Specs (including offset):
4. Rear Wheel Specs (including offset):
5. Tire brand:
6. Front Tire Specs:
7. Rear Tire Specs:
8. Rolled Fenders:
9. Pulled Fenders:
10. Suspension Set up:
11. Camber:
12. Spacers?:
13. Any Issues?:
14. PICTURESS LOTS OF THEM:

And most importantly thank you all who share

[Kevin_Trxn]

I'll go first. Got a ton of people asking for my specs

1. Wheel Make: BBS
2. Wheel Model: RSII (rs793)
3. Front Wheel Specs (including offset): 19x9+16
4. Rear Wheel Specs (including offset): 19x9.5+22
5. Tire brand: Hankooks v12
6. Front Tire Specs: 225/35/19
7. Rear Tire Specs: 235/35/19
8. Rolled Fenders: Yes
9. Pulled Fenders: No
10. Suspension Set up: UAS bagged suspension
11. Camber: Maxed Front Camber Plates about -2.8 and rear camber is at -2.5 at ride height which is 2.75 inches from fender to lip
12. Any Issues?: None surprisingly, I have full scrub radius at any height (except fully slammed…duh). I have lost waffle caps and locking nut on the freeway though… so wouldn't recommend RSIIs unless you are ready for the headache
13. PICTURESS LOTS OF THEM:

[Onizukachan]

I’d start with looking at the threads for show me your aftermarket 18s or after market 19s or even the 20s thread of you know your sizing.

Then check the gallery on fitment industries.

I’ve posted my specs and photos on those places as have many many others.

[Kevin_Trxn]

Originally Posted by Onizukachan

I'd start with looking at the threads for show me your aftermarket 18s or after market 19s or even the 20s thread of you know your sizing.

Then check the gallery on fitment industries.

I've posted my specs and photos on those places as have many many others.

Do you have links for those
18" and 19" threads?

The search on mobile is horrid.

[_baz]

Originally Posted by Kevin_Trxn

Do you have links for those
18" and 19" threads?

The search on mobile is horrid.

Would be good to have a fresh thread as the stanced / slammed thread is a little all over the place. Just need people to remember to actually post all the specs

[visionaut]

There’s a whole Tech Forum here on wheels, tires & fitment. Many threads, many Qs/As.

Is it easily/fully searchable? All specs listed every time? Nope. No single thread, regardless of how *official* it is ever will.. starting over yet again doesn’t cut it.

At least put this new thread in that correct section… splitting this info off yet again in this section doesn’t really help…

[Kevin_Trxn]

Originally Posted by visionaut

There's a whole Tech Forum here on wheels, tires & fitment. Many threads, many Qs/As.

Is it easily/fully searchable? All specs listed every time? Nope. No single thread, regardless of how *official* it is ever will.. starting over yet again doesn't cut it.

At least put this new thread in that correct section… splitting this info off yet again in this section doesn't really help…

Put it in the photo thread because I'm a visual learner lol
But noted
I don't have mod permissions to transfer the thread

Also doesn't look liked it's received well so that's that

If this thread dies…at least I tried

[harmz]

What size lips did you get made for rs2? I have just got my 793 stepped up to 19 inch with 2” lips did you have the back pads milled ? I have got slightly narrower build 8.5 fronts. I’m fitting them on a f36

[Kevin_Trxn]

Originally Posted by harmz

What size lips did you get made for rs2? I have just got my 793 stepped up to 19 inch with 2" lips did you have the back pads milled ? I have got slightly narrower build 8.5 fronts. I'm fitting them on a f36

2.5" lip
They are milled 3mm… I think

[harmz]

Originally Posted by Kevin_Trxn

2.5" lip
They are milled 3mm… I think

Okay thanks! Yeah mine seem to fit fine, did you have any issues with bolts snapping? With the hidden bolts or was yours welded to make it "2 piece" again

[Kevin_Trxn]

Originally Posted by harmz

Okay thanks! Yeah mine seem to fit fine, did you have any issues with bolts snapping? With the hidden bolts or was yours welded to make it "2 piece" again

Welded

[djgreg1200]

Originally Posted by Kevin_Trxn

I'll go first. Got a ton of people asking for my specs

1. Wheel Make: BBS
2. Wheel Model: RSII (rs793)
3. Front Wheel Specs (including offset): 19x9+16
4. Rear Wheel Specs (including offset): 19x9.5+22
5. Tire brand: Hankooks v12
6. Front Tire Specs: 225/35/19
7. Rear Tire Specs: 235/35/19
8. Rolled Fenders: Yes
9. Pulled Fenders: No
10. Suspension Set up: UAS bagged suspension
11. Camber: Maxed Front Camber Plates about -2.8 and rear camber is at -2.5 at ride height which is 2.75 inches from fender to lip
12. Any Issues?: None surprisingly, I have full scrub radius at any height (except fully slammed…duh). I have lost waffle caps and locking nut on the freeway though… so wouldn't recommend RSIIs unless you are ready for the headache
13. PICTURESS LOTS OF THEM:

This build is FIRE!!!!