10-08-2018, 06:11 PM | #1 |
Private
29
Rep 81
Posts |
Thrust Arm and Bushing Replacement (DIY?)
Hey all,
Just got back from the dealer after a coolant flush and it appears like my thrust arm bushings are severely worn. To make a long story short, the dealer has quoted:
To make it better they've only quoted the actual ~$70 bushings and bolts as the only parts required. Not the actual thrust arm(s). So safe to say I'm a bit salty. I know lower control arms are easy in our cars but what's the difficulty like on replace both thrust arms (w/ bushings pre-installed)? Something that I can do in the garage w/ a pretty good set of tools? Anyone else have a similar experience? My car is a 2014 335 xdrive for reference. Thanks! |
10-08-2018, 07:39 PM | #2 |
Brigadier General
4007
Rep 3,535
Posts
Drives: 328d Wagon, M2 Comp, i4 eD35
Join Date: Sep 2016
Location: Bay Area, CA
|
Why would you want to replace the actual arms unless you need to?
If you have a hydraulic press to remove the bushings from the arms you might be able to DIY it, but given your post asking about it, I get the feeling you don't have the tools required. The price they quoted you doesn't sound too out of line (for my area anyways). Either way, you can find the various procedures here. |
Appreciate
0
|
10-08-2018, 09:58 PM | #3 | |
Private
29
Rep 81
Posts |
Quote:
|
|
Appreciate
0
|
10-09-2018, 09:11 AM | #5 |
Major
477
Rep 1,467
Posts |
I just replaced mine. Both of them went by 65K miles. I have an x drive as well.
The job is very easy on a lift. Make sure you remove the axle bolts on each side (buy new axle bolts; they are one time use) These arms are known to go bad around 60K miles on modern BMWs. $700 for this job is asinine.
__________________
2014 EBII 435ix - Stage 2+ Dragy: 0-60 3.61; 60-130 10.18
2020 MG M340ix - Dragy: 0-60 3.48 2018 LBB X4M40i - Stock Dragy: 0-60 4.85 |
Appreciate
1
BMW DIY Guy3039.00 |
08-20-2019, 07:49 PM | #6 | |
Second Lieutenant
57
Rep 215
Posts |
Quote:
|
|
Appreciate
0
|
08-21-2019, 01:23 PM | #7 |
Brigadier General
3039
Rep 3,010
Posts
Drives: 2019 M2 Competition
Join Date: Jan 2017
Location: Maple Valley WA
|
I have every possible bushing for the F32 from Powerflex, and am working on bushing replacement DIYs on them all and will post them here for sure.
That said, I am still very much learning and trying to find the minimalist approach for all of the process.. leveraging the rear sway bar guide to replace all the bushings there, looking to the fronts for more guidance etc. Still don't have it all down yet, and waiting on some tools and parts, but welcome any advice as well. Good to know on the axle bolts? Not seen that anywhere yet..
__________________
Check out my BMW DIY Channel on YouTube! E, F and G series projects from Active Autowerke, Bimmertech, Kies Motorsports, AvinUSA, Karbonius Composites and more!
** YouTube BMW DIY Guy ** 'Nimona' G87 M2 Build Thread 'Lillith' F87 M2 Competition Build Thread |
Appreciate
1
haagm58809.50 |
08-21-2019, 02:41 PM | #8 | |
Captain
432
Rep 785
Posts |
Quote:
Since BMW recommends the control arms be replaced for every other bushing change, we prefer to sell these as a pre-assembled set. So that's one reason? Dunno if they are being honest or not, but I guess maybe the arms get fatigued from repeated articulation. Given that they also sell their bushings without the arm, it doesn't seem like they are just trying to rip the customer off by offering them pre-installed in new arms. This Dealer could be jumping the gun and suggesting they replace them on the first bushing change to make more money. |
|
Appreciate
0
|
08-21-2019, 03:36 PM | #9 | |
Enlisted Member
9
Rep 39
Posts |
Quote:
Could be because they're aluminum and pressing bushings in and out widens the hole out of tolerance (or maybe weakens it). On my ZO6, GM recommended not changing the ball joints at all but replacing the entire arm. |
|
Appreciate
0
|
09-04-2019, 11:22 AM | #10 | |
Brigadier General
3039
Rep 3,010
Posts
Drives: 2019 M2 Competition
Join Date: Jan 2017
Location: Maple Valley WA
|
Quote:
https://www.realoem.com/bmw/enUS/sho...diagId=31_0942
__________________
Check out my BMW DIY Channel on YouTube! E, F and G series projects from Active Autowerke, Bimmertech, Kies Motorsports, AvinUSA, Karbonius Composites and more!
** YouTube BMW DIY Guy ** 'Nimona' G87 M2 Build Thread 'Lillith' F87 M2 Competition Build Thread |
|
Appreciate
0
|
09-04-2019, 11:44 AM | #11 | |
Major
477
Rep 1,467
Posts |
Quote:
|
|
Appreciate
0
|
09-04-2019, 11:49 AM | #12 |
Brigadier General
3039
Rep 3,010
Posts
Drives: 2019 M2 Competition
Join Date: Jan 2017
Location: Maple Valley WA
|
Ok, I am unclear of which bolt you are talking about then? I am going to be removing both arms (each side of course) to replace the bushings and want to make sure I am ready and have everything I need.
Thanks!
__________________
Check out my BMW DIY Channel on YouTube! E, F and G series projects from Active Autowerke, Bimmertech, Kies Motorsports, AvinUSA, Karbonius Composites and more!
** YouTube BMW DIY Guy ** 'Nimona' G87 M2 Build Thread 'Lillith' F87 M2 Competition Build Thread |
Appreciate
0
|
09-04-2019, 11:59 AM | #13 |
Brigadier General
4007
Rep 3,535
Posts
Drives: 328d Wagon, M2 Comp, i4 eD35
Join Date: Sep 2016
Location: Bay Area, CA
|
You don't have axle collar bolts since you're RWD. Control arm swaps are very fast and easy for your vehicle since you just have to undo the ball joint bolts on the knuckle and the bolts holding the bushings to the subframe.
__________________
-328d Wagon Build Log (with helpful reference links)
-My YouTube Channel for some of the best DIYs and in depth information Please don't PM me for suspension recommendations unless interested in paid private consultations. |
Appreciate
1
BMW DIY Guy3039.00 |
09-04-2019, 12:16 PM | #14 |
Brigadier General
3039
Rep 3,010
Posts
Drives: 2019 M2 Competition
Join Date: Jan 2017
Location: Maple Valley WA
|
Thanks man, I really appreciate the wisdom as always!
__________________
Check out my BMW DIY Channel on YouTube! E, F and G series projects from Active Autowerke, Bimmertech, Kies Motorsports, AvinUSA, Karbonius Composites and more!
** YouTube BMW DIY Guy ** 'Nimona' G87 M2 Build Thread 'Lillith' F87 M2 Competition Build Thread |
Appreciate
0
|
09-04-2019, 12:38 PM | #15 |
Major
477
Rep 1,467
Posts |
If rwd, this is the easiest job. If awd, you have to remove axle bolt and move the entire boot out of the way.
|
Appreciate
0
|
09-04-2019, 03:39 PM | #16 | |
Brigadier General
3039
Rep 3,010
Posts
Drives: 2019 M2 Competition
Join Date: Jan 2017
Location: Maple Valley WA
|
Quote:
https://www.newtis.info/tisv2/a/en/f...ounts/GaGZPQz2 Wonder if it is worth doing so?
__________________
Check out my BMW DIY Channel on YouTube! E, F and G series projects from Active Autowerke, Bimmertech, Kies Motorsports, AvinUSA, Karbonius Composites and more!
** YouTube BMW DIY Guy ** 'Nimona' G87 M2 Build Thread 'Lillith' F87 M2 Competition Build Thread |
|
Appreciate
0
|
09-04-2019, 10:15 PM | #17 | |
Captain
480
Rep 681
Posts |
Quote:
__________________
2016 328ix F31 - SOLD!
2006 997.1 C4S |
|
Appreciate
0
|
Post Reply |
Bookmarks |
Tags |
diy, thrust arm |
Thread Tools | Search this Thread |
|
|