BMW F30 3 Series Coding DIY - Code Auto Start Stop, DVD, Folding Mirrors, Etc.

Piggin · 02-03-2016, 04:00 PM

Hi Shawn,

Could you please send me the link for latest E-Sys software and psdzdata.

Thanks very much

shawnsheridan · 02-03-2016, 04:33 PM

Quote:

Originally Posted by Piggin

Hi Shawn,

Could you please send me the link for latest E-Sys software and psdzdata.

Thanks very much

PM sent.

phattbam · 02-03-2016, 06:36 PM

anyone with luck getting the 'eyebrows" enabled along with the angel eyes?

///MPower15 · 02-04-2016, 12:04 PM

Quote:

Originally Posted by shawnsheridan

I would shut F80 down for 30 minutes and then try again. The IP port frequently gets jammed up and needs full power down to reset.

Is this a common issue with F-series cars? I was unable to code a car because I could not connect, but I previously coded it just fine.

M5Beast_NYC · 02-04-2016, 12:13 PM

Could you please send me the link for the esys file as well as the data file to download. thank you!

shawnsheridan · 02-04-2016, 12:36 PM

Quote:

Originally Posted by ///MPower15

Is this a common issue with F-series cars? I was unable to code a car because I could not connect, but I previously coded it just fine.

Yes, quite common.

shawnsheridan · 02-04-2016, 12:37 PM

Quote:

Originally Posted by Carbonm3ny

Could you please send me the link for the esys file as well as the data file to download. thank you!

PM sent.

Piggin · 02-04-2016, 01:28 PM

Thanks very much Shawn

kayhan · 02-04-2016, 01:43 PM

Hello I am a newbie.. I have the cable ready but need sw and instructions for coding.. could you pls help

shawnsheridan · 02-04-2016, 02:01 PM

Quote:

Originally Posted by kayhan

Hello I am a newbie.. I have the cable ready but need sw and instructions for coding.. could you pls help

PM sent.

maexx · 02-05-2016, 05:10 AM

Hi Shawn,

first of all: good job! I really appreciate your efforts.

I just installed a front PDC kit and need to do the coding now. (Had rear already insalled before) I am familiar with the basics and know that "508" has to be added to the FA but I'm not sure if that's all I need and how to do it exactly.

Thanks for your help!

shawnsheridan · 02-05-2016, 06:13 AM

Quote:

Originally Posted by maexx

Hi Shawn,

first of all: good job! I really appreciate your efforts.

I just installed a front PDC kit and need to do the coding now. (Had rear already insalled before) I am familiar with the basics and know that "508" has to be added to the FA but I'm not sure if that's all I need and how to do it exactly.

Thanks for your help!

After adding 508 to FA, you need to write FA to car, then VO Code affected modules in car (e.g. PDC, TRSVC, CIC/NBT).

PM sent.

maexx · 02-05-2016, 06:20 AM

Quote:

Originally Posted by shawnsheridan

After adding 508 to FA, you need to write FA to car, then VO Code affected modules in car (e.g. PDC, TRSVC, CIC/NBT).

PM sent.

Hi Shawn,

do you know which modules are affected in particular?

Greetings and thank you

shawnsheridan · 02-05-2016, 06:23 AM

Quote:

Originally Posted by maexx

Hi Shawn,

do you know which modules are affected in particular?

Greetings and thank you

The ones I listed in my post above. If you do not have TRSVC, then omit it.

mutters · 02-05-2016, 09:43 AM

Hi Shawn,
New owner, cable on order, feeling confident..

Could you please send me the link for latest E-Sys software and psdzdata.

many thanks

shawnsheridan · 02-05-2016, 10:43 AM

Quote:

Originally Posted by mutters

Hi Shawn,
New owner, cable on order, feeling confident..

Could you please send me the link for latest E-Sys software and psdzdata.

many thanks

PM sent.

ted.makrys · 02-05-2016, 01:37 PM

Hi shawnsheridan ,

Could I please get access to the software etc. ordering a cable now.

Thanks!
Ted

maexx · 02-05-2016, 01:50 PM

Quote:

Originally Posted by shawnsheridan

The ones I listed in my post above. If you do not have TRSVC, then omit it.

Okay did it, worked for the CIC. By PDC you mean the REM?! I tried to code that one but it gave me an error in which it says: cafd_.......... NotExecutable

Do you have any clue on what is going on?

shawnsheridan · 02-05-2016, 02:29 PM

Quote:

Originally Posted by ted.makrys

Hi shawnsheridan ,

Could I please get access to the software etc. ordering a cable now.

Thanks!
Ted

PM sent.

shawnsheridan · 02-05-2016, 02:31 PM

Quote:

Originally Posted by maexx

Okay did it, worked for the CIC. By PDC you mean the REM?! I tried to code that one but it gave me an error in which it says: cafd_.......... NotExecutable

Do you have any clue on what is going on?

No, when you Read ECU, you should have a PDC module.

maexx · 02-05-2016, 02:55 PM

Quote:

Originally Posted by shawnsheridan

No, when you Read ECU, you should have a PDC module.

Well, I dont have a PDC module but there are many PDC parameters in the REM module. (attached a list of modules)

shawnsheridan · 02-05-2016, 02:56 PM

Quote:

Originally Posted by maexx

Well, I dont have a PDC module but there are many PDC parameters in the REM module. (attached a list of modules)

It is possible in F20 that REM is for PDC then. Front Sensor then may be in FEM_BODY. I would VO Code CIC/NBT, REM, and FEM_BODY then.

02-03-2016, 04:00 PM	#9901
Piggin Private First Class 97 Rep 155 Posts Drives: M440i Join Date: Feb 2016 Location: UK - South Wales iTrader: (0)	Hi Shawn, Could you please send me the link for latest E-Sys software and psdzdata. Thanks very much
	Appreciate 0 Quote

02-03-2016, 06:36 PM	#9903
phattbam Major General 180 Rep 5,822 Posts Drives: '17 Protonic Blue i3 REx Join Date: Sep 2007 Location: sf area iTrader: (21)	anyone with luck getting the 'eyebrows" enabled along with the angel eyes?
	Appreciate 0 Quote

02-04-2016, 12:13 PM	#9905
M5Beast_NYC Major 158 Rep 1,314 Posts Drives: 15 M5 Join Date: Apr 2010 Location: NYC iTrader: (6)	Could you please send me the link for the esys file as well as the data file to download. thank you!
	Appreciate 0 Quote

02-04-2016, 01:28 PM	#9908
Piggin Private First Class 97 Rep 155 Posts Drives: M440i Join Date: Feb 2016 Location: UK - South Wales iTrader: (0)	Thanks very much Shawn
	Appreciate 0 Quote

02-04-2016, 01:43 PM	#9909
kayhan Registered 0 Rep 1 Posts Drives: f30 320i Join Date: Feb 2016 Location: istanbul iTrader: (0)	Hello I am a newbie.. I have the cable ready but need sw and instructions for coding.. could you pls help
	Appreciate 0 Quote

02-05-2016, 05:10 AM	#9911
maexx New Member 0 Rep 6 Posts Drives: F20 Join Date: Feb 2016 Location: Ger iTrader: (0)	PDC Hi Shawn, first of all: good job! I really appreciate your efforts. I just installed a front PDC kit and need to do the coding now. (Had rear already insalled before) I am familiar with the basics and know that "508" has to be added to the FA but I'm not sure if that's all I need and how to do it exactly. Thanks for your help!
	Appreciate 0 Quote

02-05-2016, 09:43 AM	#9915
mutters Registered 0 Rep 3 Posts Drives: f31 330d m sport Join Date: Feb 2016 Location: somerset uk iTrader: (0)	Hi Shawn, New owner, cable on order, feeling confident.. Could you please send me the link for latest E-Sys software and psdzdata. many thanks
	Appreciate 0 Quote

02-05-2016, 01:37 PM	#9917
ted.makrys New Member 0 Rep 5 Posts Drives: 2007 335i 6AT Join Date: Apr 2013 Location: Canada iTrader: (0)	Hi shawnsheridan , Could I please get access to the software etc. ordering a cable now. Thanks! Ted
	Appreciate 0 Quote