[Galip1993]

Hello everybody, I have a quick question regarding Wheel/tire size. I don’t have much knowledge regarding f30 wheels/tire size fitments.

Is this size,

Wheel size: 19x8.5 ET 35 (front). Tire size: 225/40/19.
Wheel size: 19x9.5 ET 35 (rear). Tire size: 255/35/19.
too big of a setup for a F30 with h&r sport lowering springs? If anybody has a similar setup, let me know.

[TheFanatic]

Originally Posted by Galip1993

Hello everybody, I have a quick question regarding Wheel/tire size. I don’t have much knowledge regarding f30 wheels/tire size fitments.

Is this size,

Wheel size: 19x8.5 ET 35 (front). Tire size: 225/40/19.
Wheel size: 19x9.5 ET 35 (rear). Tire size: 255/35/19.
too big of a setup for a F30 with h&r sport lowering springs? If anybody has a similar setup, let me know.

You'll be fine

[j2nicee]

Originally Posted by Canadared

I plan on getting wheels rebuilt, 19x9.5 +30, 19x10.5 +40 with some camber. Rub yay or nay?

Will all depend on tires and how low you go. I was going to go with a similar set up but I was told I may run into inner clearance so I dropped down to a 9/10 set up. The fenders on these cars are very weak apparently so keep that in mind.

[Canadared]

Originally Posted by j2nicee

Will all depend on tires and how low you go. I was going to go with a similar set up but I was told I may run into inner clearance so I dropped down to a 9/10 set up. The fenders on these cars are very weak apparently so keep that in mind.

Oh I know, I ran 19x9 +35 fronts with 8mm spacers and jacked up my fender pretty good backing out of my drive way. Mind you it was hella low so it comes with the territory. Gonna get Millway camber plates to help out

[Waltabeast]

19x9.5 +33
19x10.5 +38

[justanthony1]

Originally Posted by himynameskevin

Been a minute but figured I'd check back in

Originally Posted by himynameskevin

Been a minute but figured I'd check back in

Damn this is hot! Share specs!!

[Arf01]

Hi all,

I have 405m replicas (i was told they were OEM but recently found out otherwise).

Current setup (staggered)
Fronts - 245/30/20 - 8.5j
Rears - 265/30/20 - 9.5j

I've managed to crack one of the font rims (welded a couple of times but keeps cracking) and there are no offsets stamped in any wheel. I have managed to find simailr rims but needed to know my current setup as I'm after the same look.

Any ideas what my current setup is ? Pics below:
Car is standard stock m sport suspension
No idea if they are 40/45 or 35/38 or something completely different.

[iron_mike_]

Originally Posted by himynameskevin

Been a minute but figured I'd check back in

Love this. Care to share your specs? what rims are these?

[Grecg]

Apex arc 8

19x9 et 28 245/35
19x9.5 et 33 265/35

[j2nicee]

Clean, gives a little RS-II vibe.

[Spanky_F30]

Current side pic

[jackthew]

Quick question

I am looking at 18x8.5 ET 35 fronts, and 18x9.5 ET 35 rears for my car, with 255/40 all around.

Is ET35 too little for the rear?

I will be installing BR Racing BR Series coils very soon after getting the wheels.

[tomppa]

Originally Posted by Dippydo

No. I had 42 in the rear on a 10.5 and with the KW I rubbed at about 10 oclock on the rear fender. The kws are too soft. Even at the highest point and I turned rebound to the hardest part it still rubbed. My H&R coils before did not though, but they were a stiffer ride. I went and had my hubs shaved to be a 44 offset and no more rubbing.

Damn, can you just fix your hubs to lathe and shave 2mm off!?
How do you know it won't fail on high speed corner at 220 km/h?

Then, could you do the same for wheels too?

[kern417]

Originally Posted by jackthew

Quick question

I am looking at 18x8.5 ET 35 fronts, and 18x9.5 ET 35 rears for my car, with 255/40 all around.

Is ET35 too little for the rear?

I will be installing BR Racing BR Series coils very soon after getting the wheels.

It's way more stretch than you need to fill out the fenders. You may need spacers for good fitment, but then the wheels will poke.

[Grecg]

Originally Posted by j2nicee

Clean, gives a little RS-II vibe.

Thanks 🙏🏽 RS II's are some of my favorites!

[PKEF32]

My new Vertini config

[boiet671]

Hi! Got the same setup, 19x9.5 et35 255/35/19 square and my front wheels are touching the strut! Are you running any spacers? I’m on bcbr coilovers. Any info on this would help! Nice ride too!

Originally Posted by Ih8usrnms

the front wheel specs are 19x9.5 et35 tires are 245/30/19 i believe. the rears are 19x10.5 265/30/19 not sure of the offset.

[M3EW]

Want new wheels already

[j2nicee]

Originally Posted by SLVR_F30

Want new wheels already

Stupid clean man!

Whats you diffuser set up? 3 piece? Looking for a replacement one right now.

[M3EW]

Originally Posted by j2nicee

Stupid clean man!

Whats you diffuser set up? 3 piece? Looking for a replacement one right now.

https://www.ebay.com/itm/Rear-Bumper....m46890.l49292

https://www.ebay.com/itm/AK-Style-Ca....m46890.l49292

Here you go man. Wish it was a three piece lol. I had to do a lot of research before hand to see if this would work since, from what I see, I'm the only one that has this setup. I bought the PSM style rear skirt extensions from China and then the AK diffuser from Taiwan. The rear extensions were an easy install, but the diffuser took an hour or two cuz it's hard af to fit. Total price I paid was about $700 shipped+tax. Also the wait time took about 6 weeks for the pieces come in since it's overseas. Hope this helps

[RobF30]

Originally Posted by jeremyuhh

Cut springs

Are these M4 rims?

[j2nicee]

I think 18/19 are the best sizes for the F30 chassis. 17s look a little too small and 20s are just a tad big.