BMW 3-Series and 4-Series Forum (F30 / F32) | F30POST
>
Lane change warning failure after coding F36
| 10-12-2023, 08:36 AM | #1 |
|
New Member
3
Rep 18
Posts |
Lane change warning failure after coding F36
I have done some codind with Vgate trough BimmerCode and now after a few minutes driving it shows me this and it deactivates the button. It also disables cruise control and I think the blind assist(i am not sure). If i press the button it works again for some time.
Can you guys please help me to reverse what I have done? I have wrote most of the coding, I attached the picture. |
| 10-12-2023, 05:56 PM | #2 |
|
Colonel
 
753
Rep 2,103
Posts |
What are your error codes?
__________________
Help each other: if you manage to fix your issue (especially with help from this forum), don't be a d*ck and disappear. Follow-up by posting the solution so you can help others.
|
|
Appreciate
1
StefanAnton3.00 |
| 10-12-2023, 08:20 PM | #3 |
|
Colonel
1324
Rep 2,084
Posts |
Bimmercode backs up each module before applying the coding. Restore the backup for I'd assume FEM and see if that fixes it.
|
|
Appreciate
1
StefanAnton3.00 |
| 10-14-2023, 02:14 PM | #5 |
|
Colonel
753
Rep 2,103
Posts |
If you cannot undo your coding as suggested above, may want to check with ISTA+ the actual BMW specific error codes, as they not only provide better details but also suggest a fix.
The error codes you posted are hard to make out, but seems like your radar sensors and the (associated?) LIN signal in the side mirror have issues. Do you have Lane Change Warning? Was it working before? It is working now or only at times? Does your warning triangle in the mirror(s) work? Can you check (example: with Bimmercode), if your LIN-options coding for your mirrors is correct for your car?
__________________
Help each other: if you manage to fix your issue (especially with help from this forum), don't be a d*ck and disappear. Follow-up by posting the solution so you can help others.
|
|
Appreciate
0
|
| 10-14-2023, 02:28 PM | #6 |
|
New Member
3
Rep 18
Posts |
I resolved the problem. I coded the blind spot assist to start at 10 km/h and that seemd to be the problem.
Thanks! |
|
Appreciate
1
B58 _gran_coupe_669.50 |
| 12-12-2024, 04:20 PM | #7 | |
|
New Member
2
Rep 27
Posts |
Quote:
What did you change it back to? Having the same issue after coding it to that |
|
|
Appreciate
0
|
| 01-07-2025, 02:46 PM | #8 | |
|
New Member
3
Rep 18
Posts |
Quote:
|
|
|
Appreciate
0
|
| 02-14-2025, 04:19 AM | #9 | |
|
Registered
0
Rep 2
Posts |
Quote:
I also changed the blind spot assist to 10 km/h recently, it was at 50 km/h. Will try each setting to see what works. 50 is way too high imo. |
|
|
Appreciate
0
|
| 02-17-2025, 12:06 PM | #10 | |
|
New Member
2
Rep 27
Posts |
Quote:
|
|
|
Appreciate
0
|
| 02-17-2025, 02:21 PM | #11 |
|
Colonel
753
Rep 2,103
Posts |
You can code it lower without an error, for example at 20 Mph. But it will go off every time you turn in a multi-lane intersection, as it detects the car(s) also turning next to you on either side. Better to set it at a speed which is higher than the speed you are likely to be making in a turn in an intersection.
https://f30.bimmerpost.com/forums/sh...1238969&page=9
__________________
Help each other: if you manage to fix your issue (especially with help from this forum), don't be a d*ck and disappear. Follow-up by posting the solution so you can help others.
|
|
Appreciate
0
|
Post Reply |
| Bookmarks |
| Thread Tools | Search this Thread |
|
|
