11-05-2020, 07:59 PM | #1 |
¯\_(ツ)_/¯
945
Rep 1,762
Posts |
Need brake torque specs
Well....since the TIS is gone I can't find a source for various torque specs on the F30. I need need the caliper bolt and guide pin torque values for FRONT 335 GREY BREMBO calipers and REAR 328 STOCK 1 PISTON calipers.
Thanks!
__________________
Tensioner/belt DIY | Side skirt extension DIY
Apex SM-10/DWS06+ | 400m/X-ice Xi3 | Injen Exhaust | Stoptech SS Lines | 335 Front Brakes Hawk HPS 5.0 | RBF600 | ER Charge Pipes | Wagner Evo Comp 2 FMIC |
11-17-2020, 01:13 PM | #2 |
Captain
207
Rep 603
Posts |
Ugh, nasty! Loved NewTIS
Found it as picture in a German Forum Front Caliper M12x1.5 -> 110 Nm Rear Caliper M12x1.5 -> 30 Nm and then add 90 Degrees Guide Pin Front and Rear 28 Nm https://www.motor-talk.de/bilder/dre...208133236.html
__________________
335i F31 RWD in SB || Powertrain: Active Autowerke Flash Tune Stage 1 | AA Charge Pipe | AA FMIC | GFB DV+ | xHD Trans-Flash | Quaife LSD | Cyba 3.5" Carbon tips || Chassis: 20" 405M | Wiechers Strut Bar | Rear M-Diffusor || Brakes: 18" M-Perf Brake orange 370/345 | EBC YellowStuff pads all around || Various: LED bulbs: Fog-L. front | Turn Signal f&r | Brake L. | Reverse L. | Rear L. | Rear Fog L.
|
11-19-2020, 01:49 AM | #3 | |
Enlisted Member
3
Rep 34
Posts |
Quote:
|
|
Appreciate
0
|
11-19-2020, 05:41 PM | #4 | ||
Lieutenant Colonel
991
Rep 1,934
Posts |
Quote:
__________________
F30 335iX | Remus Axleback | Fabspeed Catted DP | VRSF Comp IC | 18X9 ET35 19lb MT1 | 255/40/18 ECS | Ohlins RT Millway Street | Millway Control Arm Bushings | Turner Endlinks | TMH 75mm 14x1.5 Studs | BMW MPerf LSD | XDelete | Pipercross Filter | MHD Stg2 93
|
||
Appreciate
0
|
11-25-2020, 08:29 PM | #5 |
Private First Class
62
Rep 120
Posts |
Heads up, the rear caliper bracket bolts are TTY (torque to yield), you should replace them every time you loosen.
And you'll want to make sure the car is jacked up nice and high, it was a nightmare getting those off on my car on Esco jack-stands set at a lower position. Wasn't enough clearance to get a breaker bar on them and not enough room for an impact gun. |
Appreciate
0
|
01-13-2021, 01:04 PM | #6 |
Lieutenant
153
Rep 414
Posts |
I'm about to do the rear brakes on my 2016 328ix LCI single piston and found this post that confirms the details above with a screen shot in English from TIS
https://f30.bimmerpost.com/forums/sh....php?t=1354470 Seems like you are not supposed to turn an extra 90 degrees if you reuse the M12x1.5 bolt, but as bthomas518 mentioned the repair guide says they should be replaced. Last edited by GreenF30N26; 01-13-2021 at 01:53 PM.. |
Appreciate
0
|
01-15-2021, 07:27 PM | #7 |
Private First Class
96
Rep 153
Posts
Drives: 2014 428xi Sport Line
Join Date: Jul 2017
Location: Keller, TX
|
I can still get on the TIS site. I had to register but still can access.
|
Appreciate
0
|
Post Reply |
Bookmarks |
|
|