[benny888]

here are my datalog,,, are those normal ?

also i dun get y when i floor the gas, it will kickdown to 2nd gear ? what should i do ?

thanks

first pull
http://www.bootmod3.net/log?id=5b1becafd10b437faba93c2e

2nd pull
http://www.bootmod3.net/log?id=5b1bedaed10b437faba93c32

[rjd_F30]

Originally Posted by benny888

here are my datalog,,, are those normal ?

also i dun get y when i floor the gas, it will kickdown to 2nd gear ? what should i do ?

thanks

first pull
http://www.bootmod3.net/log?id=5b1becafd10b437faba93c2e

2nd pull
http://www.bootmod3.net/log?id=5b1bedaed10b437faba93c32

Logs look ok to me, but I am not an expert. The car will drop to the lowest possible gear when you floor it because you are hitting the kick down switch. It is designed to do this to offer the best acceleration, which typically means being in the lowest gear possible.

[benny888]

Originally Posted by rjdnyy224

Logs look ok to me, but I am not an expert. The car will drop to the lowest possible gear when you floor it because you are hitting the kick down switch. It is designed to do this to offer the best acceleration, which typically means being in the lowest gear possible.

nice the hear my logs are ok, btw do i need to do another pull that not hitting the kick down switch to avoid it drops to 2nd? thanks

[rjd_F30]

Originally Posted by benny888

nice the hear my logs are ok, btw do i need to do another pull that not hitting the kick down switch to avoid it drops to 2nd? thanks

Like I said just because I said they look good doesn't necessarily mean they are, just saying . Hitting the kick down switch is perfectly okay when running logs.

[benny888]

Originally Posted by rjdnyy224

Like I said just because I said they look good doesn't necessarily mean they are, just saying . Hitting the kick down switch is perfectly okay when running logs.

ooo xddd , lets wait someone else to take a look with my logs then

[lukeiswright]

You're running rich and your timing isn't good at all. For some reason I can only see a few things on your logs you're not showing all the parameters

[benny888]

Originally Posted by lukeiswright

You're running rich and your timing isn't good at all. For some reason I can only see a few things on your logs you're not showing all the parameters

oo really ? wt should i do with the map? send the logs to ptf ?

strange that u cant see all the parameters, how abt clicking the parameter at the bottoms? attached is screenshot of my logs

thanks

[lukeiswright]

Originally Posted by benny888

oo really ? wt should i do with the map? send the logs to ptf ?

strange that u cant see all the parameters, how abt clicking the parameter at the bottoms? attached is screenshot of my logs

thanks

Here's a screenshot of my log. You see how the timing is all the same number and that my AFR is around 12 at high rpm. I would go to your downloaded map and request an update saying you're running rich and timing looks a lil funny. They should fix it for you

[rjd_F30]

Good point, definitely running rich past 3rd.

Timing is odd, but so are IATs. You started the pull at 120° ish and ended at about the same. Usually IATs start low and end high, assuming you're running the stock intercooler. Seeing as the car naturally pulls timing when IATs get too high, this may be the source of the issue? Not that these logs show a "pull" of timing, but perhaps the DME is spazzing out trying to implement stock failsafes on a tuned car? idk, just a thought.

benny888, what octane gas were you running and what temperature was it outside when this log was recorded?

Either way, if you feel it's necessary, open a support ticket with PTF and send them these logs and see what they say. They will give a straightforward and correct answer, along with proposing a solution.

[benny888]

Originally Posted by lukeiswright

Here's a screenshot of my log. You see how the timing is all the same number and that my AFR is around 12 at high rpm. I would go to your downloaded map and request an update saying you're running rich and timing looks a lil funny. They should fix it for you

wow !!! i even get negative numbers and ever seen them in same number

just requested update on the map btw thanks so much

[benny888]

Originally Posted by rjdnyy224

Good point, definitely running rich past 3rd.

Timing is odd, but so are IATs. You started the pull at 120° ish and ended at about the same. Usually IATs start low and end high, assuming you're running the stock intercooler. Seeing as the car naturally pulls timing when IATs get too high, this may be the source of the issue? Not that these logs show a "pull" of timing, but perhaps the DME is spazzing out trying to implement stock failsafes on a tuned car? idk, just a thought.

benny888, what octane gas were you running and what temperature was it outside when this log was recorded?

Either way, if you feel it's necessary, open a support ticket with PTF and send them these logs and see what they say. They will give a straightforward and correct answer, along with proposing a solution.

yes i am running full stock intercooler/ intake ,,, the only mod on my car is the eisenmann axle back exhaust

im running 93octane gas (98 RON in HongKong) and the temperature outside was 31 degrees Celsius

thanks

[lukeiswright]

Originally Posted by benny888

wow !!! i even get negative numbers and ever seen them in same number

just requested update on the map btw thanks so much

No problem dude keep us updated

[benny888]

Originally Posted by lukeiswright

No problem dude keep us updated

sure , lets see how ptf reply

[jflow72]

Hey! Your the first guy I've seen with the same DME as me. After I looked at your logs I thought they looked some what similar to mine. I noticed you posted in another thread your DME version. My timings are also a bit diff from 1-4 and the AFR is also rich in the upper rpm. Let me know what your hear from PTF. I noticed version 2 of the tunes feel smoother (specifically 2500rpm - 3000rpm) to me so I'm currently running version 2. I'm watching for your update for sure. I had messaged them a couple weeks ago because I thought I had some tune issues, but they said everything looked good (I had messaged them with logs of version 2).

I have a downpipe and I have an FMIC coming, but this log is stock other than the tune.

http://www.bootmod3.net/log?id=5b17e5c5d10b432af151f8d9
This log is version 3 stage 1 93 octane just from the other day.

http://www.bootmod3.net/log?id=5b02ccc1d10b4326703f2bfe
Also just for fun this is a log of my stock tune from a couple weeks ago.

If anybody more knowledgeable wants to chime in I'm all for learning.

[benny888]

Originally Posted by jflow72

Hey! Your the first guy I've seen with the same DME as me. After I looked at your logs I thought they looked some what similar to mine. I noticed you posted in another thread your DME version. My timings are also a bit diff from 1-4 and the AFR is also rich in the upper rpm. Let me know what your hear from PTF. I noticed version 2 of the tunes feel smoother (specifically 2500rpm - 3000rpm) to me so I'm currently running version 2. I'm watching for your update for sure. I had messaged them a couple weeks ago because I thought I had some tune issues, but they said everything looked good (I had messaged them with logs of version 2).

I have a downpipe and I have an FMIC coming, but this log is stock other than the tune.

http://www.bootmod3.net/log?id=5b17e5c5d10b432af151f8d9
This log is version 3 stage 1 93 octane just from the other day.

http://www.bootmod3.net/log?id=5b02ccc1d10b4326703f2bfe
Also just for fun this is a log of my stock tune from a couple weeks ago.

If anybody more knowledgeable wants to chime in I'm all for learning.

heyy hi haha we got the same old old DME version

yup , i feel the v2 ots is smoother than the v3 as well

i got drivetrain malfunction twice with the stage1 custom map before the OTS came out,,,, checked with my fd , they said should be sth related to the ignition timing to cause the knocking problem,,,,also told me engine/ piston will break if i keep using that map....

after that i flashed to OTS v1 - v3 , seems like no more drivetrain malfuction. however, i am still afraid that my engine will break, so i finally did a datalog that day. find out that ignition time look strange that has different number across 1-4 , so i post it here to see if any expert to tell me wt exactly happen to my map if any, and seems really there some issue with the timing

so lets wait what pft will do with it for now

PS: i flashed back to stock tune for now until they have new map lollll

[benny888]

update: they updated the map, they ask me to re-download the OTS v3 and try , it should fix the problem .... however, i dun have time to test it yet, will post a new datalog as soon as i tested it

[1slow320i]

Would appreciate it if anyone could look at my data logs as well I’m also have engine knock on stage 1 91 octane. Will have data logs linked below.

log 1

Log 2