[kav247]

Hi

I’m pretty new to coding so wanted a simple step on how I can code the LCI stalk into my pre LCI F33

Everything works except the indicators that don’t turn off with the turning of the steering.

I also wanted to calibrate the steering sensors before I actually started driving it but the option was not available

Any help direction on what I need to do I much appreciated

A simple step by step would really help

[TheNine90]

LIN_VARIANTE_SZL
change to the one wihout _r_
LIN_VARIANTE_SPARE_SZL
change same as the above

[kav247]

Is this VO to change in FEM_BODY?

All the yellow lines all indicate to this szl wrong version issue?

[TheNine90]

No. edit the FEM cafd and change the fdl

[kav247]

Thank you

I will try this tomorrow morning and feedback to you

Thank you once again

[kav247]

How do I know which one to edit

[Siki78]

You need launcher for this. I can code it remotley

[mig2830]

You have it in ISTA fault code 030351 wrong LIN.

You cannot VO code the LCI SZL as your car is telling the system its pre LCI. You need to FDL code the SZL in the FEM. And here it becomes a litle bit dificult as the LCI ones is not self explaining as the pre LCI. Cant remember the code you need but somting like ?????2 ending at 2

[kav247]

I have team viewer

[Siki78]

You have pm

[kav247]

Thank you Siki78

You really took the time out today and resolved the issue for me where I installed a pre LCI stalk on my F33 and installed a LCI stalk giving me an error for invalid version installed

I can’t thank you enough 🙏🏽

[phoenixorion]

Hello,
I have installed the pre-lci steering column stalk on my 2018 F30, but the indicator does not function for long press. Can you help me choose the correct code?

[NeoSaw]

Hello, I have the same problem as kav247. I installed an LCI SLZ in a preLCI. Everything coded and now I have error 030351.
Everything works except that the turn signal doesn't go off when you steer back.

@Siki78 can you maybe help me too? or write what I need to change? Unfortunately that's not clear from this thread.

@Kav247 maybe you can help me? Siki helped you. Maybe you still know the solution.

I am thankful for every help.

[kav247]

Hi

Unfortunately Siki did this for me remotely as I don’t have the correct software

I am hoping he can reach out to you and help you as he was amazing resolving my issue

[TheNine90]

Originally Posted by NeoSaw

Hello, I have the same problem as kav247. I installed an LCI SLZ in a preLCI. Everything coded and now I have error 030351.
Everything works except that the turn signal doesn't go off when you steer back.

@Siki78 can you maybe help me too? or write what I need to change? Unfortunately that's not clear from this thread.

@Kav247 maybe you can help me? Siki helped you. Maybe you still know the solution.

I am thankful for every help.

You need to change the lin variant of the szl in FEM. You can do it using and supported coding tools.

[NeoSaw]

Which Lin variant should I use? I think there are 5 or 6

Do you perhaps have the correct coding value?

CODDT_Byte_00_SLZ_Lin=LHZ_active

LIN_Variant_LRE=lre_tcl_lhz

LIN_Variant_SLZ=slz_4Band

LRE_Verbaut=active

I coded that

Do you recognize an error?

[NeoSaw]

Thx for Helping ,maybe Siki will help me

[TheNine90]

LIN_Variante_SZL
If you only change SZL with lci without changeing anything else choose same option but with "r"

[NeoSaw]

Originally Posted by TheNine90

LIN_Variante_SZL
If you only change SZL with lci without changeing anything else choose same option but with "r"

So I just have to code LIN_Variant_SZL differently. all other values ​​remain the same?

[Siki78]

Vo code fem with you original vo then change LIN_VARIANTE_SZL
Same like you have just to have r
Example if you original is szl_aic_4Band change to szl_r_aic_4Band

[NeoSaw]

Originally Posted by Siki78

Vo code fem with you original vo then change LIN_VARIANTE_SZL
Same like you have just to have r
Example if you original is szl_aic_4Band change to szl_r_aic_4Band

does the _r_ then stand for pre LCI?

Ok, I'll try it and get back to you. Thank you in advance.

In any case, an SLZ from the LCI 2020 works in the preLCI from 2012 + steering wheel heating

[Siki78]

_r_ mean lci car. If you install lci stalk on prelci car you need to use _r_