[jtuds]

How does the rear spoiler adhere? And am I naive thinking it would be super easy to self install?

[tissot]

Originally Posted by jtuds

How does the rear spoiler adhere? And am I naive thinking it would be super easy to self install?

I used double sided tape and it is very easy to install.

[Blake P]

Just me or is there no description on how to replace the rear valence?

[Kankles]

For those of you that have installed the M perf rocker panels...they sell the decals (film strips) separately. How big are the film strips? Would the side panels look weird without them? Thanks for any info

[steveMizdaman]

Originally Posted by Blake P

Just me or is there no description on how to replace the rear valence?

def no description. only reason I bumped up this thread is bc I just ordered a rear diffuser its on back order until aug 12th.

[bosbrucec]

Can the front spoiler be removed without damage to the factory M sport bumper if the spoiler gets scraped? I'm guessing the glue used will ruin the parts of the M sport factory bumper that are covered by this kit, and, even though this looks good, I'd only do it if it were a sacrificial part that could be removed if scraped and go back to factory, given how low it sits.

[Presario]

Originally Posted by steveMizdaman

def no description. only reason I bumped up this thread is bc I just ordered a rear diffuser its on back order until aug 12th.

Did you guys figure out how to install the rear? I just placed an order and I'm wondering where the instructions went. Thanks so much fellas.

[steveMizdaman]

Originally Posted by Presario

Did you guys figure out how to install the rear? I just placed an order and I'm wondering where the instructions went. Thanks so much fellas.

believe its just double sided tape and few clips or screws...suppose to be very simple from what I read on the forums. didn't actually find the instructions though. I wouldn't worry though. when are you suppose to get yours?

[DangerousTacos]

Originally Posted by bosbrucec

Can the front spoiler be removed without damage to the factory M sport bumper if the spoiler gets scraped? I'm guessing the glue used will ruin the parts of the M sport factory bumper that are covered by this kit, and, even though this looks good, I'd only do it if it were a sacrificial part that could be removed if scraped and go back to factory, given how low it sits.

Very curious about this myself. Been debating doing this kit come spring...

[Presario]

Originally Posted by steveMizdaman

believe its just double sided tape and few clips or screws...suppose to be very simple from what I read on the forums. didn't actually find the instructions though. I wouldn't worry though. when are you suppose to get yours?

Thanks so much for the info Steve. Really appreciate it. I'm supposed to get my rear diffuser any day now. I'll report back once I get it installed. Thank again!

[Presario]

Originally Posted by bosbrucec

Can the front spoiler be removed without damage to the factory M sport bumper if the spoiler gets scraped? I'm guessing the glue used will ruin the parts of the M sport factory bumper that are covered by this kit, and, even though this looks good, I'd only do it if it were a sacrificial part that could be removed if scraped and go back to factory, given how low it sits.

I'm totally wondering the same thing. When I lower my car in the near future, I'm worried about the m sport bumper and not the diffuser. My local shop said that they can install it without the betalink and just the double sided tape so that it can be removed later. We would still be utilizing the screws of course. Since the bumper is polyurethane, I'm sure the bends and flexes from the diffuser being sacrificed shouldn't be an issue. I'll most likely be doing this so I can report back with my results.

[steveMizdaman]

Originally Posted by Presario

Thanks so much for the info Steve. Really appreciate it. I'm supposed to get my rear diffuser any day now. I'll report back once I get it installed. Thank again!

I was suppose to have mine 3 days ago but its been pushed back to aug 20th now

[Presario]

Originally Posted by steveMizdaman

believe its just double sided tape and few clips or screws...suppose to be very simple from what I read on the forums. didn't actually find the instructions though. I wouldn't worry though. when are you suppose to get yours?

Hey Steve, so I picked mine up today and installed it. The reason there are no instructions for the rear diffuser is because it's really straightforward. No double sided tape in the process. The diffuser is held in place by 7 screws along the lower outer edge and a series of tabs on the upper part where it meets the bumper. Remove the screws and access the outermost tab from the underside of the car. You can reach between the exhaust pipe. Pull down and push the first tab out. It's a little tough but once the first one comes out, the others pop out in sequence. Reverse the process and done!

[steveMizdaman]

Originally Posted by Presario

Hey Steve, so I picked mine up today and installed it. The reason there are no instructions for the rear diffuser is because it's really straightforward. No double sided tape in the process. The diffuser is held in place by 7 screws along the lower outer edge and a series of tabs on the upper part where it meets the bumper. Remove the screws and access the outermost tab from the underside of the car. You can reach between the exhaust pipe. Pull down and push the first tab out. It's a little tough but once the first one comes out, the others pop out in sequence. Reverse the process and done!

that's great...I never like working with double sided tape...thanks for the details on it. any pictures?

[SteveChester]

Originally Posted by Jason

Below you can download the entire official installation instructions guide for retrofitting the M Performance Aerodynamics Package to the F30 3 Series.

Quoted installation time is approximately 3 hours and the guide includes all necessary part numbers. Enjoy!

* Click on image to download installation guide in PDF *

Attachment 808601

Anybody got the instructions to install the side films?

[JN1]

Don't forget to "Re-assemble the car in a logical manner"

See #9 on the last page.

[Who?]

the front bumper doesnt need to be pulled out right?

[Seraphblade@sg]

Anyone knows if the m perf rocker panels really require drilling? That doesn't really make this very DIY friendly...

[AweSam8]

Originally Posted by Presario

Hey Steve, so I picked mine up today and installed it. The reason there are no instructions for the rear diffuser is because it's really straightforward. No double sided tape in the process. The diffuser is held in place by 7 screws along the lower outer edge and a series of tabs on the upper part where it meets the bumper. Remove the screws and access the outermost tab from the underside of the car. You can reach between the exhaust pipe. Pull down and push the first tab out. It's a little tough but once the first one comes out, the others pop out in sequence. Reverse the process and done!

So no drilling whatsoever? Just use existing bolts and screws?

[LACSTER]

@kidluvsole

[Presario]

Originally Posted by AweSam8

So no drilling whatsoever? Just use existing bolts and screws?

Whoa sorry I missed this post. Yeah no drilling whatsoever. Uses the screws that are already there. You'll do it in like 10 minutes.

[retiredmarine]

I am getting ready to do the front spoiler and side skirt extensions. Anyone have any tips or tricks?