[shawnsheridan]

Originally Posted by koppermonty

I used the above solution via Esys in the end to clear the restraint/airbag error code. It worked wonders via this method.

[tke743]

Hi Shaun, could you send me a link to the tool 32 Please?

[shawnsheridan]

Originally Posted by tke743

Hi Shaun, could you send me a link to the tool 32 Please?

PM sent.

[F30sam]

Hey Shaun, could you send me a link to the tool 32 Please?

[shawnsheridan]

Originally Posted by F30sam

Hey Shaun, could you send me a link to the tool 32 Please?

PM sent.

[autosyonal]

Hi ,shauwn
First
thanks for e-sys en ptzdata finally get it connected to the car dit not code yet
i strugled with the home made cable all conections where correct and now connection posible finally i change the obd connector it was a old one and dit not connect wel on the cars obd poort

wen i read and save fa and read and save svt do i have then all back up files wen someting gows wrong ? and how to back UP if sometings gows wrong

Can you send me link voor İsta-D , Ediabas , tool 32 i

[shawnsheridan]

Originally Posted by autosyonal

Hi ,shauwn
First
thanks for e-sys en ptzdata finally get it connected to the car dit not code yet
i strugled with the home made cable all conections where correct and now connection posible finally i change the obd connector it was a old one and dit not connect wel on the cars obd poort

wen i read and save fa and read and save svt do i have then all back up files wen someting gows wrong ? and how to back UP if sometings gows wrong

Can you send me link voor İsta-D , Ediabas , tool 32 i

Why you make cable rather than just buy ENET cable off eBay or Amazon is beyond me in first place. At less than $20 USD, it simply is not worth the time to make one, even if you have parts laying around.

As for backups, they are worthless. If you wnat to reset ECU, simply VO Code it. PM sent.

[autosyonal]

Shawn
you are 100% right, had I known before, I would have bought a ready cable
but I could not wait 1 week delivery time
so I thought I have everything in the house just a resistor of 510 ohm to buy soldering and ready. Not so no connection got checked all 10 times apparently my old obd plug was not good and gave bad contact to the obd gate of the car bad luck

[shawnsheridan]

Originally Posted by autosyonal

Shawn
you are 100% right, had I known before, I would have bought a ready cable
but I could not wait 1 week delivery time
so I thought I have everything in the house just a resistor of 510 ohm to buy soldering and ready. Not so no connection got checked all 10 times apparently my old obd plug was not good and gave bad contact to the obd gate of the car bad luck

I give you an A for the effort though.

[madnutt]

Shawn can you please help?

I have tool32 and ENET cable. Fault is cc-Id 108 on a 2014 435i. Could you let me know what job to load and which options to clear this. Thank you.

[shawnsheridan]

Originally Posted by madnutt

Shawn can you please help?

I have tool32 and ENET cable. Fault is cc-Id 108 on a 2014 435i. Could you let me know what job to load and which options to clear this. Thank you.

Clear Fault Codes:

Launch C:\EDIABAS\Bin\TOOL32.EXE
Hit F3
Load C:\EDIABAS\Ecu\F01.PRG
In the "Select Job: F01" window, select FS_LOESCHEN_FUNKTIONAL
Hit F5
"Results" window should show "JOB_STATUS = OKAY"

Note: fs_lesen_funktional only read fault codes, FS_LOESCHEN_FUNKTIONAL will delete it.

[tarekelsakka]

shawnsheridan I know you're probably already tired of me, but could you please send me the Tool32 link? Thanks a lot!

[shawnsheridan]

Originally Posted by tarekelsakka

shawnsheridan I know you're probably already tired of me, but could you please send me the Tool32 link? Thanks a lot!

PM sent.

[dieselg5]

Hi Shawn,

Can you please send me Tool32 as well?

[shawnsheridan]

Originally Posted by dieselg5

Hi Shawn,

Can you please send me Tool32 as well?

PM sent.

[plikmuny]

Can i get Tool 32 link also Shawn ? i have an error throwing for long time and i need to clear that.

[shawnsheridan]

Originally Posted by plikmuny

Can i get Tool 32 link also Shawn ? i have an error throwing for long time and i need to clear that.

PM sent.

[ozkangadow]

hello shawn, could you please send me the link of tool32?
thanks

[shawnsheridan]

Originally Posted by ozkangadow

hello shawn, could you please send me the link of tool32?
thanks

PM sent.

[duszmic]

Hi,
I know that this topis was discuss few times, nether the less can we make a summary of retrofit pdc in f10 ?

1. im my e sys i have "." instead folder names - why ?
2. what functions i should acivated in esys to enable rear camera ? i have install emulator and camera. Can i ask for instruction step by step ?

[pirrup]

Hi shawn,

Can you please send me the link to tool32 also?

Thanks!

[shawnsheridan]

Originally Posted by duszmic

...1. im my e sys i have "." instead folder names - why ?...

(...) means the PSdZData is Trimmed. Trimmed PSdZData means either E-Sys has Incorrect Target Connection, or you do not use E-Sys Launcher to open E-Sys, or you use E-Sys Launcher PREMIUM but select wrong car Series or this particular ECU CAFD is not mapped in E-Sys Launcher's CAFD Mapping Database, or you have insufficient Java Memory in order for E-Sys Launcher to map it.