07-10-2018, 04:05 AM | #1 |
Registered
4
Rep 3
Posts |
Dashboard lid up like a christmass tree
Hey guys, I’m kinda new to the forum, but not new to the bmw’s. This is my 6th one I think, but never had a similar problem. I read the forum all the time and usually find the answers i need without making a specific post about it... Well, things change
So, long story short...since few months I’ve swapped my trustworthy e90 with a f30 2013 328xi Sport Edition. To be honest...awesome car. Now about the issues...One is not new, comes and goes. - Sometimes when i drive for a while and stop /at the gas station i.e/ adterwards the car goes into limp mode. No messagea, no nothing. Just starts but wont drive. After restarting a few times it goes again. Dont know when it’s gonna happen again. Fout on the OBD - U1164. Trough inpa - “Valvetronic actuator position sensor short circuit or line interruption” I would like to have an idea about this if anyone has of course Second problem..big one... - few days ago while driving i’ve got the “Passenger restraint system” fout. Havent been gone since. No errors on the OBD reader..bit it’s still on. After a few days I get into the car, push the button and it went insane. Multiple system faults - abs, drivetrain malfunction, brakes etc. After restarting a few times car atarted, but the “check engine” light was on. It was on for a few days and it was gone. Few days without a problem, this weekend car was in the garage, today I try to go to work and baaam...christmas tree again. It cranked once, didnt start and...that was it. Wont start since Soo...i have the idea that maybe the battery is dead, will try to charge it tonight and see, but yeah...I’m open to ideas Has anyone had a similar or the same problem? Thank you guys in advance and greetings from The Netherlands |
07-10-2018, 10:43 AM | #3 |
Lieutenant Colonel
481
Rep 1,572
Posts |
Is your battery the original? And have you had it load tested? Any auto parts store will do it for free.
May not be the battery, but I seen some pretty weird faults, Alerts, etc. when a battery is failing. The electronic systems and the power management/monitoring system is pretty involved. |
Appreciate
0
|
07-15-2018, 10:50 AM | #4 |
Registered
4
Rep 3
Posts |
Ok, so I’ve recharged the battery...Seems not to be the problem. Still getting the same mistakes. It cranks once, doesnt start and then nothing. What I’ve noticed is that the break pedal seems a bit hard...Also i cannot change gears, even to neutral. Car is stuck in the parking spot under the building... I’m getting these errors: Brake system : drive moderately
Flat tyre monitor inactive Drivetrain malfunction... Seriously need help here guys... Nobody has even the slightest clue? |
Appreciate
0
|
07-15-2018, 11:04 AM | #5 |
Major
583
Rep 1,117
Posts
Drives: 2015 BMW M235i
Join Date: Feb 2016
Location: ontario
|
could be a faulty dme or a short circuit from installed mods? Any mods on the car?
|
Appreciate
0
|
07-15-2018, 11:05 AM | #6 |
Major
601
Rep 1,048
Posts |
Maybe it's the dash unit; maybe it's the ECU; maybe not. Without access to testing equipment, replacing one piece at a time based on clues could turn out to be a real mess. It may be time to get it towed to the dealer.
|
Appreciate
0
|
07-15-2018, 12:22 PM | #8 |
¯\_(ツ)_/¯
537
Rep 1,000
Posts |
Sounds like you bought a car that was in a flood and the computers are all messed up
|
Appreciate
0
|
08-04-2018, 11:32 AM | #9 |
Registered
4
Rep 3
Posts |
Ok, so I had a nice vacation, but I'm back and it's time to put some attention to the car. I've run the diagnostics and got quite a few things. If someone would be kind enough to look at them any help will be highly appreciated. I honestly dont know where to start from:
ACSM4 --- 0x930994 Safety battery terminal: Resistance too high 40253 No ACSM4 --- 0xC95418 No message (DME), ACSM receiver, DME/DDE transmitter 40487 No ACSM4 --- 0xC95419 Message (DME) not current, receiver ACSM, transmitter DME/ 40487 Yes DDE ACSM4 --- 0xC9542D Signal invalid (driving speed, 0x19F), transmitter ICM 40487 No CIC --- 0xE1CC00 Signal (wheel speed, K-CAN) missing 40487 No CIC --- 0xE1CC03 Message (reverse gear, 0x3B0) missing, receiver CIC, transmi 40487 No tter FRM / FEM / EGS DSC_25 --- 0x480704 DSC control unit: Internal, runtime error 40487 No DSC_25 --- 0x4809AB DSC: Undervoltage in vehicle 40487 Unknown DSC_25 --- 0x480AB8 DSC control unit: Vehicle start with vehicle moving or driving c 40487 Unknown ondition unknown DSC_25 --- 0xD35452 No message (drive train 3 data, 251.1.4), receiver DSC, trans 40487 Yes mitter DME / DDE DSC_25 --- 0xD35557 No message (wheel torque powertrain 1, 0X08F), receiver DS 40487 Yes C, transmitter DME/DDE DSC_25 --- 0xD35558 No message (wheel torque powertrain 2, 41.3.4), receiver DS 40487 Yes C, transmitter DME/DDE DSC_25 --- 0xD3556D No message (wheel torque powertrain 3, 0X145), receiver DS 40487 Yes C, transmitter DME/DDE DSC_25 --- 0xD35570 No message (wheel torque powertrain 4, 0X0DC), receiver DS 40487 Yes C, transmitter DME/DDE DSC_25 --- 0xD35646 No message (accelerator pedal angle, 0X0D9), receiver DSC, 40487 Yes transmitter DME/DDE DSC_25 --- 0xD3569A No message (data transmission train drive, 237.1.2), receiver 40487 Yes DSC, transmitter DME/DDE DSC_25 --- 0xD35744 No message (data, drive train 2, 0X3F9), receiver DSC, trans 40487 Yes mitter DME/DDE DSC_25 --- 0xD358E1 No message (torque, crankshaft 1, 0X0A5), receiver DSC, tra 40487 Yes nsmitter DME/DDE DSC_25 --- 0xD35A08 No message (wheel torque powertrain 6, 61.3.4), receiver DS 40487 Yes C, transmitter DME/DDE DSC_25 --- 0xD35A53 Signal(actualsteeringangle,frontaxle,57.1.2)invali d,trans 40487 Yes mitter ICM/EPS DSC_25 --- 0xD35A57 ICM interface (longitudinal acceleration, centre of gravity, ID: 40487 Yes 0X199) Signal invalid DSC_25 --- 0xD35A62 Signal (lateral acceleration, centre of gravity, 0X19A) invalid, t 40487 No ransmitter ICM/EPS DSC_25 --- 0xD35B3F No message (wheel torque, drive 5, 40.3.4), receiver DSC, tra 40487 Yes nsmitter DME/DDE DSC_25 --- 0xD35C1B No message (status, energy generation, 0X1BA), receiver DS 40487 Yes C, transmitter DME/DDE DSC_25 --- 0xD36D44 Signal (longitudinal torque distribution, front axle/rear axle, 19. 40487 Yes 3.4) invalid, transmitter VTG EKP301 --- 0xCED400 No message (delivery quantity, 0x137), receiver EKPS, transm40487 Yes itter DME/DDE EPS_25 --- 0x4823D4 EPS voltage supply: Undervoltage in vehicle 40487 Unknown 2 Operations report, VIN: F542981 25-7-2018 22:14:53, 3/15 EPS_25 --- 0xD51744 No message (drive train data 2, 230.0.2), receiver EPS, trans 40487 Yes mitter DME / DDE EPS_25 --- 0xD51A53 ICM interface (actual steering angle, front axle, 57.1.2): Signal 35158 Unknown invalid EPS_25 --- 0xD51C1B No message (power generation status, 232.1.2), receiver EPS 40487 Yes , transmitter DME / DDE EPS_25 --- 0xD51C1F No message (specified electrical power, 232.0.2), receiver EP 40487 Yes S, transmitter DME/DDE FEM_20 --- 0x8040B1 Wake-up line to the intelligent battery sensor IBS: Short circuit 40487 Yes to B+ or line disconnection FEM_20 --- 0xD90C01 LIN master CAS_LIN: No communication 40487 No FEM_20 --- 0xD90D01 FBD receiver 1 (LIN): No LIN-slave 40487 No FEM_20 --- 0xD91573 No message (status, DSC stabilisation, 0x173), receiver FEM, 40487 No transmitter DSC FEM_20 --- 0xD915B9 No message (heat management, engine control, 0x1B9), recei 40487 Yes ver FEM, transmitter DME/DDE FEM_20 --- 0xD91654 No message (actual wheel speed, unsecured, 0x254), receive 40487 No r FEM, transmitter DSC FEM_20 --- 0xD91681 No message (vehicle electrical system, voltage value, 0x281), 40487 Yes receiver FEM, transmitter DME/DDE FEM_20 --- 0xD916ED No message (status, vehicle standstill, 0x2ED), receiver FEM, 40487 No transmitter DSC FEM_20 --- 0xD917B3 No message (power management, electric load control, 0x3B3 40487 Yes ), receiver FEM, transmitter DME/DDE FEM_20 --- 0xD917F9 No message (data, drive train 2, 0x3F9), receiver FEM, trans 40487 Yes mitter DME/DDE FEM_20 --- 0xD91FF9 No message (drive train data 2, ID 230.0.2), receiver FEM, tra 40487 Yes nsmitter DME/DDE GSB231 --- 0xCF1461 No message (diagnosis OBD engine, 0x397): Receiver EGS, t 40487 Yes ransmitter DME/DDE GSB231 --- 0xCF1501 No message (diagnosis OBD engine, 0x397), receiver EGS, tr 40487 Yes ansmitter DME/DDE GSB231 --- 0xCF1511 No message (diagnosis OBD engine, 0x397), receiver EGS, tr 40487 Yes ansmitter DME/DDE GSB231 --- 0xCF1521 Message (group fault 1 - effect during driving: considerable): 40487 Yes Receiver EGS, transmitter DME/DDE GSB231 --- 0xCF1531 Message (group fault 2 - effect on driving: possible): Receiver 40487 Yes EGS, transmitter DME/DDE GSB231 --- 0xCF1541 Message (group fault 3 - effect on driving: none): Receiver E 40407 Yes GS, transmitter DME/DDE ICM_25 --- 0x480121 ICM: internal yaw-rate signal implausible 35158 No ICM_25 --- 0x482717 ICM: Rotation-rate sensor, temporary fault 35158 No ICM_25 --- 0xD01557 No message (wheel torque powertrain 1, 41.3.4), receiver ICM 40471 No , transmitter DME/DDE ICM_25 --- 0xD01558 No message (wheel torque powertrain 2, 41.3.4), receiver ICM 40471 No , transmitter DME/DDE ICM_25 --- 0xD0156D No message (wheel torque powertrain 3, 61.3.4) missing, rece 40471 No iver ICM, transmitter DME/DDE ICM_25 --- 0xD01570 No message (wheel torque powertrain 4, 40.3.4), receiver ICM 40471 No , transmitter DME/DDE ICM_25 --- 0xD0157A Signal (wheel torque powertrain 4, 40.3.4) invalid, transmitter 37184 No DME / DDE ICM_25 --- 0xD01646 No message (angle, accelerator pedal, 40.1.4), receiver ICM, 40487 Yes transmitter DME/DDE ICM_25 --- 0xD01744 No message (data, drive train 2, 230.0.2), receiver ICM, trans 40471 No mitter DME/DDE ICM_25 --- 0xD018E1 No message (torque, crankshaft 1, 40.1.4), receiver ICM, tran 40471 No smitter DME/DDE ICM_25 --- 0xD01A08 Nomessage(wheeltorquepowertrain6,61.3.4),receiverI C 40471 No M, transmitter DME/DDE ICM_25 --- 0xD01B3F No message (wheel torque powertrain 5, 40.3.4) , receiver IC 40471 No M, transmitter DME/DDE IHKA20 --- 0xE71406 Nomessage(data,drivetrain2,0x3F9),receiverIHKA,tra ns 40487 Yes mitter DME/DDE IHKA20 --- 0xE7140E Message (crankshaft torque 1, 0xA5) missing, receiver IHKA, t 40487 Yes ransmitter DME/DDE IHKA20 --- 0xE7142B No message (power management consumer/load control, 0x3 40487 Yes B3), receiver IHKA, transmitter DME-DDE 3 Operations report, VIN: F542981 25-7-2018 22:14:54, 4/15 IHKA20 --- 0xE71442 No message (status of engine auto start, 0x30B), receiver IHK 40487 Yes A, transmitter DME IHKA20 --- 0xE71458 No message (heat management, engine control, 0x1B9), recei 40487 Yes ver IHKA, transmitter DME/DDE KOMB25 --- 0xB7F667 Instrument cluster: System time storage error 0 No KOMB25 --- 0xE11421 Instrument panel: Message for condition-based service: Mess 40487 Yes age from CBS user has failed KOMB25 --- 0xE1145C No message (display, engine speed, drive train, 0x0F3), recei 40487 Yes ver instrument cluster, transmitter DME/DDE KOMB25 --- 0xE1145E No message (data, drive train, 0x3F9), receiver instrument clu 40487 Yes ster, transmitter DME/DDE KOMB25 --- 0xE11467 No message (angle of accelerator pedal, 0x0D9), instrument p 40487 Yes anel receiver, DME/DDE transmitter KOMB25 --- 0xE1146F Message (status, stabilisation of Dynamic Stability Control, 0x 40487 No 173) missing, receiver instrument panel, transmitter DSC KOMB25 --- 0xE1147A No message (status, engine fuel consumption, 0x2C4), receiv 40487 Yes er KOMBI, transmitter DME / DDE KOMB25 --- 0xE11490 Nomessage(display,checkcontrolbypass,0x36E),receiv er 40487 No KOMBI, transmitter DSC KOMB25 --- 0xE12C11 Signal (driving speed, 0x1A1) invalid, transmitter ICM / DSC 40487 No KOMB25 --- 0xE12C1F Signal(vehicledistancecovered,0x2BB)invalid,transm itterI 40487 No CM/DSC REM_20 --- 0x030115 Power window, rear door on driver's side: invalid characteristic 40487 Yes curve, no normalisation present REM_20 --- 0x030120 Powerwindow,reardoorondriver'sside:systemisnotstan d 40487 Yes ardised. REM_20 --- 0x030195 Window regulator, passenger's side door, rear: invalid charact 40487 Yes eristic curve, no normalisation present REM_20 --- 0x0301A0 Window regulator on passenger's side door, rear: system is n 40487 Yes ot normalised. REM_20 --- 0xE5940E No message (drive train 2 data, 0x3F9), receiver REM, transm 40487 Yes itter DME/DDE REM_20 --- 0xE59435 No message (power management, consumer control, 0x3B3), 40487 Yes receiver REM, transmitter DME/DDE TRSVC01 --- 0xCA940A No message (drive train 2 data, 0x3F9), receiver TRSVC, tran 40487 Yes smitter DME / DDE TRSVC01 --- 0xCAAC02 Signal (vehicle speed, 0x1A1) invalid, transmitter ICM 40487 No TRSVC01 --- 0xCAAC0A Interface DME / DDE (data, drivetrain 2, 0x3F9): signal invalid 37184 No unknown --- S 0392 No communication possible with: Engine electronics 40487 Unknown ZGW_01 --- 0x801C20 ZGM: central fault memory full - no control-unit fault 40487 Yes There are like 10 more pages but hardly anything different. |
Appreciate
0
|
08-04-2018, 11:49 AM | #10 |
Second Lieutenant
125
Rep 298
Posts |
Sounds like bad battery or its connections. What kind of voltage you get directly from battery and compare it to engine bay terminals. Here is one older post with fault 930994:
https://f30.bimmerpost.com/forums/sh....php?t=1438620 |
Appreciate
0
|
Post Reply |
Bookmarks |
|
|