08-08-2019, 04:40 PM | #2 |
New BMW owner
139
Rep 621
Posts
Drives: BMW 316d, BMW F40 116d
Join Date: Jan 2012
Location: Belgium
|
Is it a 330e or 335i Active Hybrid?
|
Appreciate
0
|
08-08-2019, 05:11 PM | #4 |
New BMW owner
139
Rep 621
Posts
Drives: BMW 316d, BMW F40 116d
Join Date: Jan 2012
Location: Belgium
|
Do you have any issues onboard?
Like any fault messages etc? |
Appreciate
0
|
08-08-2019, 05:14 PM | #5 |
Lieutenant
161
Rep 474
Posts |
I added a drop in filter from afe and replaced my oil cooler gasket and ofhg. Ever since I've gotten those codes. But they clear. The dc to dc doesn't want to clear though.
__________________
J. D. Cordier
|
Appreciate
0
|
08-09-2019, 01:10 PM | #6 | |
Colonel
588
Rep 2,302
Posts |
Quote:
Fault description Diagnosis monitors the DC/DC converter (support for voltage supply of head unit during engine start for vehicles with automatic Start-Stop function) and the signal line between the front electronics module (FEM) and DC/DC converter. The fault is identified when there is an open circuit, short to B+ or B- on the signal line or when the DC/DC converter signals a fault. Condition for fault identification Supply voltage greater than 8.5 V Terminal 30B on Condition for fault memory entry The fault code is entered whenever it exists for 100 ms. Action in service Check line and plug connections between FEM and DC/DC converter for short-circuit and open circuit. If the wiring and the plug connections are OK, replace the DC/DC converter. Fault effect and breakdown warning Possible malfunction of head unit (audio, video, navigation) while starting engine (MSA). Driver information ------------ Service instruction ------------- If there are no problems, i would not take the error seriously or read the error memory with another program. |
|
Appreciate
1
jcordier160.50 |
08-09-2019, 04:05 PM | #7 |
Lieutenant
161
Rep 474
Posts |
Thank you for the detailed description. Under the action in service. Do you know anything about where those parts are. I haven't ever heard of the FEM or a dc/dc converter before.
__________________
J. D. Cordier
|
Appreciate
0
|
08-10-2019, 03:24 AM | #8 | |
Colonel
588
Rep 2,302
Posts |
Quote:
https://www.newtis.info/tisv2/a/en/f...erter/GGlzwmNo Here the wiring diagram (A173=FEM, N5=DC/DC converter). https://www.newtis.info/tisv2/a/en/f...erter/GRyPpin9 Here an instruction how to get to the FEM. https://www.newtis.info/tisv2/a/en/f...les/1VnYgUVO8c |
|
Appreciate
1
jcordier160.50 |
08-10-2019, 09:44 AM | #9 | ||
Lieutenant
161
Rep 474
Posts |
Quote:
__________________
J. D. Cordier
|
||
Appreciate
0
|
08-14-2019, 08:15 PM | #10 |
Lieutenant
161
Rep 474
Posts |
That other code went away, but I just used bimmer code and now there's new code that won't go away. Any help is appreciated.
__________________
J. D. Cordier
|
Appreciate
0
|
08-14-2019, 10:37 PM | #11 |
Lieutenant
161
Rep 474
Posts |
Nvm. I got it to delete the code once I turned my ac off and turned the engine off. Once I started it back up. It magically disappeared.
__________________
J. D. Cordier
|
Appreciate
0
|
05-12-2020, 05:17 PM | #12 | |
Registered
0
Rep 4
Posts |
Quote:
Hi, I have same problem after flashing all ecu except headunit, you say error is gone how did you resolve it?, is it by changing dc/dc converter ? Thank you |
|
Appreciate
0
|
07-20-2020, 01:44 PM | #13 | |
Registered
0
Rep 4
Posts |
Quote:
Finally I boat a new dc conveter, a surprise when I want change it, my car doesn’t have dc converter, I don’t understand why ista show this error, is it possible that problem is in battery which is never change it (my car production is 11/11) Last edited by ready750; 12-30-2020 at 04:38 AM.. |
|
Appreciate
0
|
12-15-2020, 04:53 AM | #14 | |
Registered
0
Rep 4
Posts |
Quote:
Finally problem resolved by doing some FDL into dme ecu and fem ecu Now into ista all is green |
|
Appreciate
0
|
Post Reply |
Bookmarks |
|
|