[jkwhar]

Originally Posted by boltinvader

My ISTA isn´t working...

This is the link to my VO
https://picload.org/view/ddpriidw/esys.png.html

I put 507 and 508 in it

And my Middle Console Button isnt working too. is there any solution?

Remove 507.

507 is for rear pdc only and 508 is for front and rear. You can't have both 507 and 508 vo.

[boltinvader]

Originally Posted by jkwhar

Remove 507.

507 is for rear pdc only and 508 is for front and rear. You can't have both 507 and 508 vo.

Thx got it working


But what is the Problem with the Button in the Middle Console. It is still not working

[jkwhar]

Originally Posted by boltinvader

Thx got it working


But what is the Problem with the Button in the Middle Console. It is still not working

Did you add the wire from the ICM to the center console buttons?

The instructions state that a cable should connect pin 2 on the console to the ICM and on my car that was already connected.
What the instructions are missing is pin 1 and in the end the connections should be:
Centre Console <-> ICM
PIN1 GN/GE(Green/Yellow) wire <-> PIN28
PIN2 GE/BL(Yellow/Blue) <---------> PIN6 should already be connected
PIN3 <-------------------------------> PIN13 should already be connected

[boltinvader]

Originally Posted by jkwhar

Did you add the wire from the ICM to the center console buttons?

Yes I connect these wires. Just trying to get INPA working to test the PDC Sensors

[jkwhar]

Originally Posted by boltinvader

Yes I connect these wires. Just trying to get INPA working to test the PDC Sensors

Did you VO code the REM, ICM, and HU_NBT/HU_CIC? Sounds like you didn't code the ICM maybe?

[Moto-XXX]

Originally Posted by Icydubloon

Just did the retrofit. As a note for others, you need to connect both of the following wires for the PDC on/off switch to work.

CC PIN1 to ICM PIN28
CC PIN2 to ICM PIN6

My (new) center console switch has the buttons for traction control, sport/eco up down buttons, and the PDC button.

If you have rear PDC, the PDC button will work without having to code front PDC. This is a nice check to perform before moving on to other parts of the install/coding.

So to be able to switch of my rear PDC I only have to install the button and nothing else?

[Jhnblckwood]

U don't "have" too. It will engage when u put car in reverse but u also must have a rem that has the pins for pdc.

[Jhnblckwood]

Will engage when in reverse and turn off when in drive for a certain amount of time, u can set the time with coding.

[r2p]

Hello

I have wired and coded everything, but i get the error:

0x803232 PDC Sensor programming faulty

All sensors in the front have the self error,
someone had that already?

Thank you for help.

[2ippy]

Hi chaps,

I have rear PDC only on my 2017 f31, and want to disable PDC when reversing with trailer.

Someone mentioned in this thread, no coding required, for the PDC button.



What is the part number for the PDC wire, to ICM?

Any pics of you routing the wire?

And the plug goes into the ICM? and you put the 2 wires in the correct pins on the existing loom plug, for the console PDC switch side?

[atzebmw]

Normally, the rear PDC automatically shuts off when you have a trailer on it.
Has the trailer hitch been retrofitted?

[2ippy]

Yes, westfalia towbar, from a well known fitter my end.

[atzebmw]

Was the retrofit coded?

[2ippy]

not that i know of, dedicated wire kit. The fog lights do turn off when hooked up.

[atzebmw]

OK, I just searched the internet and found out that if you install the retrofit kit from Westfalia, it will not shut off the PDC.
And then you can not code that either.

So like your first idea you need the PDC button.
The problem is that this cable does not exist singly, but only together with the entire retrofit harness.
Maybe someone can find out the individual part numbers for the plug and socket contacts.
I will also try to find out the part numbers

The plug then will be plugged into the PDC button and the 2 wires into the ICM.

wire green/yellow Pin 28
wire yellow/blue Pin 6

[2ippy]

odd that you can't code it :/

isn't there already a plug for the traction control, and sport mode settings?

[atzebmw]

Ah yes, i just saw that it is only one plug.
So you only need the pins and wires.

You also then need a new/used operating unit centre console 61319252912.
Here a picture
https://www.ecstuning.com/b-genuine-...t/61319252912/
Only for example.
You can buy it used on Ebay.

[atzebmw]

12527522387 should be the pins the plug.
The pins for the plug at the ICM i haven't found, but it could be that they are the same.

[2ippy]

nice if someone confirms that, before i commit to tearing it out and buying. The PDC console is £50

[gotomoto]

I am making my own Front PDC retrofit wiring harness. Can someone confirm the color coding for "Cable Set Front bumper 61129260019" and cable in "Install.kit, Park Distance Control,front 66202338070" are the same?

[avantix]

If anyone is looking for parts for a front and rear retrofit hit me up.

I have all the original brand new BMW parts never installed as well as 8 PDC sensors (Silverstone II) and front and rear harness.

Also have the REM module with correct pinout. Never got around to installing it.

Thanks

[GlennG]

Hey!

I'm having some issues with the coding. i get the error:

Transaktions-Report: Aktion: Codieren

Abort!
Failed to code the CAF "CAFD_000007A1_005_044_005" of "REM--72", because it is not present in the STV actual. [C250]

Any suggestions?

Don't know if it matters, but i'm currently running E-sys 3.27.1 and PSdZData_v.4.11.20_Lite