09-23-2020, 08:23 PM | #1 |
Captain
373
Rep 898
Posts
Drives: F32 428i Xdrive
Join Date: Aug 2020
Location: Texas
|
Wanting to max power, expected gains?
So as title suggest, I'd like to just see what other's experience is with my shared platform and what the highest/expected gains are
I drive a 2014 428i xdrive with an n26 If I were to go full bolt on, say max out everything I could with out touching internals, new turbo, the lot What am I looking to get power wise? And on another note, what's my mpg go down to?
__________________
|
09-23-2020, 10:36 PM | #3 |
Captain
373
Rep 898
Posts
Drives: F32 428i Xdrive
Join Date: Aug 2020
Location: Texas
|
Wow that's not a lot. I guess I'm expecting a little more from what I've seen
__________________
|
Appreciate
0
|
09-24-2020, 07:17 AM | #5 |
Lieutenant General
8243
Rep 16,079
Posts |
No matter what you do there's only so much you're going to get out of an N20/26. If it was only 170HP bone stock like a Toyota Corolla there would be a lot of room for improvement, but it's not.
|
Appreciate
0
|
09-24-2020, 09:14 AM | #6 |
Captain
373
Rep 898
Posts
Drives: F32 428i Xdrive
Join Date: Aug 2020
Location: Texas
|
Yeah that makes sense. I've got 93 luckily in my town as well as my state for the most part
__________________
|
Appreciate
0
|
09-24-2020, 09:16 AM | #7 |
Captain
373
Rep 898
Posts
Drives: F32 428i Xdrive
Join Date: Aug 2020
Location: Texas
|
Yeah it makes sense for sure, I was just confused as to what B005t did to his cause I just saw thicf30's vid on the dyno
__________________
|
Appreciate
0
|
09-24-2020, 09:32 AM | #8 |
BimmerPost Supporting Vendor
24183
Rep 190,777
Posts |
OTS Bootmod3 maps
N20 (low-compression 28i) Stage 1 91 octane: 16%HP / 20%TQ Stage 1 93 octane: 18%HP / 22%TQ Stage 2 91 octane: 20%HP / 24%TQ Stage 2 93 octane: 22%HP / 25%TQ Stage 1 E30 octane: 21%HP / 24%TQ Stage 2 E30 octane: 25%HP / 27%TQ N20 (PWG 20i) Stage 1 91 octane: up to 24%HP / up to 38%TQ Stage 1 93 octane: up to 26%HP / up to 38%TQ Stage 2 91 octane: up to 28%HP / up to 42%TQ Stage 2 93 octane: up to 30%HP / up to 42%TQ Stage 2 E30 octane: up to 33%HP / up to 45%TQ Stage 2 racegas: up to 33%HP / 45%TQ N20 (EWG 20i) Stage 1 91 octane: 48%HP / 54%TQ Stage 1 93 octane: 52%HP / 56%TQ Stage 2 91 octane: 54%HP / 58%TQ Stage 2 93 octane: 56%HP / 60%TQ Custom map will net you another 10-20% depending on how aggressive you want to go. Pure Turbo stage 2
__________________
Check out our current sale by clicking on this link!
https://x-ph.com/sale/ Phone number 702-494-9435 |
Appreciate
0
|
09-24-2020, 09:35 AM | #9 | |
Captain
373
Rep 898
Posts
Drives: F32 428i Xdrive
Join Date: Aug 2020
Location: Texas
|
Quote:
I'm a little confused though, what is PWG and EWG? And I have an n26, would that lower the top end by a significant margin?
__________________
|
|
Appreciate
0
|
09-24-2020, 09:37 AM | #10 | |
BimmerPost Supporting Vendor
24183
Rep 190,777
Posts |
Quote:
EWG is electronic (newer models)
__________________
Check out our current sale by clicking on this link!
https://x-ph.com/sale/ Phone number 702-494-9435 |
|
Appreciate
1
djacinto373.00 |
09-24-2020, 09:39 AM | #11 |
Captain
373
Rep 898
Posts
Drives: F32 428i Xdrive
Join Date: Aug 2020
Location: Texas
|
Got it ok, that's a little more what I was expecting. So what does it take to go from 300 to 382?
__________________
|
Appreciate
0
|
09-24-2020, 10:29 AM | #12 | |
Major
473
Rep 1,060
Posts |
Quote:
FBO: Catless downpipe Axle back exhaust GFB+ Turbo inlet Intake Chargepipe Turbo to intercooler pipe Intercooler (Wagner comp 2, Evolution raceworks, ATM, CSF, turner Motorsport) Tune (bm3, JB4) custom tune. Good luck.
__________________
MY13: TTE400 Stage 2 turbo.
e80 tune by Navardi Tuned. 380 whp/360 wheel torque stock block Build Thread: https://f30.bimmerpost.com/forums/sh....php?t=1742413 IG + YT: Sqwin_n20 |
|
Appreciate
1
djacinto373.00 |
09-24-2020, 10:32 AM | #13 | ||
Captain
373
Rep 898
Posts
Drives: F32 428i Xdrive
Join Date: Aug 2020
Location: Texas
|
Quote:
__________________
|
||
Appreciate
0
|
09-24-2020, 10:40 AM | #14 |
Major
473
Rep 1,060
Posts |
Something to be aware of is when you aim to go further than 350whp, it's advised to change rods and bolts minimum as the rods and bolts are known to let get above that range. It's the nature of the motor having full torque available below 2500 rpm.
__________________
MY13: TTE400 Stage 2 turbo.
e80 tune by Navardi Tuned. 380 whp/360 wheel torque stock block Build Thread: https://f30.bimmerpost.com/forums/sh....php?t=1742413 IG + YT: Sqwin_n20 |
Appreciate
1
djacinto373.00 |
Post Reply |
Bookmarks |
|
|